Unit 12 ¾" W, 6" front to back depth (325 x 150mm); 17" (430mm) min. clearance below mounting surface is required....
Search Results "Knee Clearance"
Filters
Commonly Searched Documents
-
Bobrick TrimLineSeries Countertop Mounted Paper Towel Dispenser B-526
-
Boolee Voting Booth
All side panel fabric is 300 x 300 urethane-coated polyester Design Specifications All weights and measures subject to minor variations Height: 60: Depth: 24” Width: 34" Clearance...
-
603 Toilet and Bathing Rooms
Doors are not permitted to swing into clear floor space or clearance required for any fixture except under certain conditions (603.2.3)....
-
Parking and Passenger Loading Zones [4.6]
Accessibility also includes the appropriate designation and location of spaces and passenger loading zones, their connection to an accessible route, and vertical clearance for vans....
-
4.31.2 CLEAR FLOOR OR GROUND SPACE
Figure 44 Mounting Heights and Clearances for Telephones...
-
1011.2.1 Size and Location
clear ground space Viewing Scopes 36 inches (915 mm) by 48 inches (1220 mm) positioned for forward approach to the viewing scope Provide knee...
-
1011.2.1 Size and Location
clear ground space Viewing Scopes 36 inches (915 mm) by 48 inches (1220 mm) positioned for forward approach to the viewing scope Provide knee...
-
604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
608.2.1 Transfer Type Shower Compartments
Clearance of 36 inches (915 mm) wide minimum by 48 inches (1220 mm) long minimum measured from the control wall shall be provided....
-
604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
Portable Units [4.1.2(6)]
Where ramps are provided, it is important that required door clearances are available at the required level landing....
-
General: ADA Standard Section 226.1
Section 226.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for dining surfaces and work surfaces.
-
Steelcase Series 5 Height-Adjustable Work Surface
Overhanging work surfaces allow for storage outside the legs while increasing knee space inside....
-
Footrests and Armrests
This clearance is needed for people transferring between the lift and a mobility device....
-
604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
608.2.3 Alternate Roll-In Type Shower Compartments
Figure 608.2.3 Alternate Roll-In Type Shower Compartment Size and Clearance ...
-
Wheelchair Passage Width [4.2.1] and Passing Space [4.2.2]
Additional clearance is needed for maneuvering and sway....
-
608.2.2 Standard Roll-In Type Shower Compartments
Figure 608.2.2 Standard Roll-In Type Shower Compartment Size and Clearance...
-
608.2.3 Alternate Roll-In Type Shower Compartments
Note: inside finished dimensions measured at the center points of opposing sides Figure 608.2.3 Alternate Roll-In Type Shower Compartment Size and Clearance...
-
1009.4.1 Clear Deck Space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars. Figure 1009.4.1 Clear Deck Space at Transfer Walls...
-
E2-c
Are any interior stairs along these routes configured with a cane-detectable warning or a barrier that prevents travel into the area with less than an 80-inch high head clearance so that...
-
11B-1009.4.1 Clear deck space
Where two grab bars are provided, the clear deck space shall be centered on the clearance between the grab bars. FIGURE 11B-1009.4.1 CLEAR DECK SPACE AT TRANSFER WALLS...
