When play components are located on an accessible route, the height required to transfer directly to the entry point or seat of a play component has a minimum of 11 inches (280 mm) and a...
Search Results "Bench Height"
Filters
Commonly Searched Documents
-
Entry Points and Seats
-
704.11.1 Parapet construction
The height of the parapet shall not be less than 30 inches (762 mm) above the point where the roof surface and the wall intersect....
-
1132A.4.1 Thresholds
Changes in height at interior door thresholds (e.g., floor material changes at door thresholds) shall not exceed ½ inch (12.7 mm)....
-
T304 Operable Parts
The technical requirements for operable parts include provisions on height, location, and operation....
-
Evaluation of transfers
to the higher heights (Table 13). ...
-
Participants
A total of 73 participants were enrolled consisting of 56 men and 17 women, with an average age of 45 ± 15 years, body weight of 176 ± 53 lbs and a height of 67±6 in....
-
§ 38.159(c)(5) Slope
If the height of the vehicle floor from which the ramp is deployed is 3 inches (75 mm) or less above a 6 inch (150 mm) curb, a maximum slope of 1:4 is permitted; if the height of the vehicle...
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
FIGURE INDEX
FIGURE INDEX Figure 104 Graphic Convention for Figures Figure 302.2 Carpet Pile Height Figure 302.3 Elongated Openings in Floor or Ground Surfaces Figure 303.2 Vertical Change...
-
2.6 Be Willing to File a Complaint
However, I had difficulty maneuvering my wheelchair in the locker room between the benches and the lockers. ...
-
1132A.4 Level floor or landing
Primary entry doors, required exit doors or secondary exterior doors with changes in height between the interior surface or floor level and the exterior surface or floor level shall comply...
-
611 Washing Machines and Clothes Dryers
Section 611 covers washing machines and clothes dryers and provides specifications for clear floor space, operable parts, and height. Comment....
-
Clear Floor Space [4.34.2] and Reach Ranges [4.34.3]
Maximum reach heights to controls are based on the approach provided. The reach height applies to all controls and elements available for customer activation....
-
Side Approach
Side Approach Where space is provided for a side approach, controls can be mounted at the heights allowed for side reaches....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
Lateral grab bar use
It can be noted that the lateral grab bar is used by more subjects when the transfer setup increases in level of difficulty (i.e. gap/height in combination or side guard)....
-
Comparison of Transfer Protocols
Highest Transfer Height Obtained Percentiles 5th 25th 50th 75th...
-
1009.5.4 Transfer Steps
Transfer step height shall be 8 inches (205 mm) maximum....
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
6.9 Tread Obstacles
Obstacles on beach access routes and their related resting intervals shall not exceed 1 inch (25 mm) in height measured vertically to the highest point....
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....