PIP was exclusively installed by contractors specializing in the surface material. ...
Search Results "Transfer Surface Height"
Filters
Commonly Searched Documents
-
Installation
-
The Dipstick® Floor Profiler Tool
Calculates F-numbers for runs, sections, and surfaces on site Instantly produces profile graphs on site "Instant" downloading to desktop or laptop computer Automatic zeroing Prints...
-
§ 38.113(d)(2) Exception
New cars operating in existing stations may have a floor height within plus or minus 11/2 inches of the platform height....
-
Stable
A surface is not permanently affected by expected weather conditions and can sustain normal wear and tear from the expected use(s) of the area, between planned maintenance....
-
Parallel Grab Bars
With respect to the lower grab bar at bathtubs, the specified mounting height has been changed to a range of 8 inches minimum to 10 inches maximum above the rim of the bathtub....
-
M305.2.2 Length (Section-by-Section Analysis)
extend the entire depth of the transfer surface and be a minimum of 15 inches in length....
-
Mounting Location and Height [4.30.6]
Mounting Location and Height [4.30.6] Placement of tactile signs aside doors (latch-side) provides safety since locating signs on doors that swing out is hazardous....
-
Connected Elevated Components
Connected Elevated Components When transfer systems are used, an elevated play component may connect to other elevated play components, providing an innovative, accessible route....
-
2) Where the Standard says "Changes in level are not permitted"
permitted", such as 304.2 for turning spaces: Here the standard is followed by an unenforceable advisory that says, "As used in this section, the phrase ‘changes in level’ refers to surfaces...
-
B. M301 Diagnostic Equipment Used by Patients in a Supine, Prone, or Side-lying Position and M302 Diagnostic Equipment Used by Patients in a Seated Position
Sections M301 and M302, which ensure that patients can transfer from their mobility devices onto the diagnostic equipment, share many technical requirements....
-
M305.3.2 Height (Section-by-Section Analysis)
For horizontal supports, the MDE NPRM proposed a gripping surface height of 34 inches minimum and 38 inches maximum above the standing surface....
-
11B-226.2 Dispersion
Dining surfaces required to comply with Section 11B-902 shall be dispersed throughout the space or facility containing dining surfaces for each type of seating in a functional area....
-
11B-226.2 Dispersion
Dining surfaces required to comply with Section 11B-902 shall be dispersed throughout the space or facility containing dining surfaces for each type of seating in a functional area....
-
11B-226.2 Dispersion
Dining surfaces required to comply with Section 11B-902 shall be dispersed throughout the space or facility containing dining surfaces for each type of seating in a functional area....
-
Current industry standard practices resulting from this project
and the National Concrete Masonry Association, funded research in 2002 to evaluate the vibration exposure during electric and manual wheelchair propulsion over several types of sidewalk surfaces...
-
Q2: Milling a Road Surface
What constitutes “overlays of additional material to the road surface” with respect to milling, specifically, when a roadway surface is milled and then overlaid at the same height (i.e.,...
-
226.2 Dispersion
Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces....
-
226.2 Dispersion
Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces....
-
F226.2 Dispersion
Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces. [ECTCR UFAS 5.1]...
-
Benches
The seat height should be a minimum of 17 inches to a maximum of 19 inches above the finished floor....
-
608.7 Thresholds
In transfer type shower compartments, thresholds ½ inch (13 mm) high maximum shall be beveled, rounded, or vertical....
-
1009.4.1 Clear Deck Space
A clear deck space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall....
-
608.7 Thresholds
In transfer type shower compartments, thresholds ½ inch (13 mm) high maximum shall be beveled, rounded, or vertical....
-
11B-1009.4.1 Clear deck space
A clear deck space of 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer wall....
