Findings from the Anthropometry of Wheeled Mobility Study indicate that a uniform width of at least 89.5 cm (35 in.) was required for 50% of the manual and power wheelchair users measured...
Search Results "Measuring Instrument"
Filters
Commonly Searched Documents
-
4.3.5.3 180-degree turn around an obstacle
-
Location and Size
The side rails are 20 inches minimum in length, 6 inches minimum in height above the table surface, and 1 inch measured horizontally from the adjacent edge of the table surface....
-
Toilet Paper Dispensers
provisions for toilet paper dispensers at section 604.7 of the 2010 Standards require the dispenser to be located seven inches minimum and nine inches maximum in front of the water closet measured...
-
Section 1630.2(j)(1)(i) Broad Construction; not a Demanding Standard
As Congress noted in the legislative history of the ADAAA, “[t]o be clear, the purposes section conveys our intent to clarify not only that ‘substantially limits’ should be measured by a...
-
Ramps
(See Part 2 of this document for tips on measuring running slopes and cross slopes.) If any part of the accessible route contains steps, it must be ramped....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Technical Memorandum TM 2013-14 Dining Surfaces
A measurement of 18” per person shall be used to calculate the number of seating and standing capacity of a dining surface....
-
C. FINDINGS BY THE UNITED STATES
Since 2005 the Museum has undertaken remedial measures and, in some instances, has installed state-of-the art technologies in the Museum to comply with the ADA....
-
5.1 Transfer Surface Height Recommendations
The height of the transfer surface during patient transfer shall be 17 inches minimum and 19 inches maximum measured from the floor to the top of the transfer surface....
-
Seat Width Evaluation
The additional platform width may also have been needed to accommodate larger individuals; however the size of the individual and seat width of the wheelchair were not measured and therefore...
-
1. Typical Issues
During an emergency, as a temporary measure, if additional accessible parking spaces are needed, a portable ramp can be provided in a parking space marked off by traffic cones to provide...
-
Clear Floor Space [4.16.2]
clear floor space doors cannot swing into the clear floor space required at any fixture the 18 inch water closet centerline is absolute The 18 inch dimension is measured...
-
Signage [4.6.4]
A height of at least 60 inches (measured to the bottom edge) is generally advisable (taking care not to make the sign a protruding object), although a higher height is better for signs at...
-
Mounting Location and Height [4.30.6]
Recommendation: At signs containing pictograms or other non-tactile information, this should be measured to the centerline of the raised/ Braille portion so that it is not too low (or high...
-
F. Publicity
To the extent any advertising is “in-kind,” Olympia’s compliance with this paragraph shall be measured by the fair market value of the advertising time used. ...
-
2.2 Lighting Conditions
On each trial one measurement of horizontal illuminance was manually recorded from a Minolta T-1 Illuminance meter....
-
Conclusion
perceive the world, in part, through pressure and movement of materials and surfaces against our skin, and we sense the instantaneous positions of our limbs as we move through, and take the measure...
-
Station 2-Three-Point Turn
At this station, active participants were asked to make a three-point turn and the width that they required was measured (figure 27)....
-
1.1.6
Specifications should include limits on how many local variations will be accepted and the methods by which accessible surfaces will be measured....
-
Identification [§216.5, §502.6]
Signs must be at least 60” high measured to the bottom edge so that they are visible while vehicles are parked in a space....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-221.6 Semi-ambulant seats
i) It is located within the rear 60% of the seats provided in an auditorium; or i) It is located within the area of an auditorium in which the vertical viewing angles (as measured...