Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
Search Results "Shoulder-to-Shoulder Seating"
-
M305.2.4.1 Circular Cross Section
-
M305.2.1.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be capable of supporting transfer on each side of the transfer surface.
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side.
-
M305.2.2.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be 28 inches (710 mm) long minimum and shall be positioned along the width of transfer...
-
Requirement 6 -- Reinforced Walls for Grab Bars
[See subsections ...]
-
§ 35.138(h) Prevention of fraudulent purchase of accessible seating
(h) Prevention of fraudulent purchase of accessible seating. A public entity may not require proof of disability before selling a wheelchair space....
-
Measuring Techniques
The functional reach dimensions listed above can all be measured in the traditional way by keeping the back, shoulder, and buttocks against the back of the seat and stretching the arm along...
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8...
-
5.1.3 Transfer Surface Low Height Options for M301 and M302
5.1.3 Transfer Surface Low Height Options for M301 and M302 The Committee did not agree on a final low height recommendation. Rationale for final recommendation (more detail...
-
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302 Description: Gripping surface hazards are sharp or abrasive elements that prevent an individual...
-
5.1.3 Transfer Surface Low Height
5.1.3 Transfer Surface Low Height. No agreement on final low height
-
5.1.2 Transfer Surface High Height
5.1.2 Transfer Surface High Height. The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches.
-
5.1.1 Transfer Surface Height Adjustability
5.1.1 Transfer Surface Height Adjustability. The transfer surface should have an adjustable height in small virtually continuous increments.
-
1.18 Wheelchair space, wheelchair location, or wheelchair seating
1.18 "Wheelchair space," "wheelchair location," or "wheelchair seating" shall mean and refer to a designated space in an auditorium where a person who uses a wheelchair or motorized scooter...
-
KirbyBuilt Providence Picnic Table with Maximum Seating
Tabletop & Seats: Plastic - injection molded, ribbed and reinforced Tabletop Length: 6 ft....
-
Greenfields Outdoor Fitness Two-Person Accessible Vertical Press GR2005-1-47-W
Two-Person Accessible Vertical Press GR2005-1-47-W Target muscles - secondary muscles Strengthens chest, shoulders, forearms, and triceps Can be used by two people...
-
Greenfields Outdoor Fitness Two-Person Accessible Lat Pull GR2005-1-48-W
Two-Person Accessible Lat Pull GR2005-1-48-W Target muscles - secondary muscles Strengthens back muscles, shoulders, and arm muscles Can be used by two people simultaneously...
-
Greenfields Outdoor Fitness Two-Person Accessible Chest Press GR2005-1-48A-W
Two-Person Accessible Chest Press GR2005-1-48A-W Target muscles - secondary muscles Strengthens chest, shoulders, upper and mid abs, forearms, and triceps Can be...
-
Can an operator require a person to transfer from a wheelchair to a vehicle seat?
Section 37.165(e) of the DOT ADA regulations allows persons who use wheelchairs to transfer to a vehicle seat, if one is available....
-
Can an operator require a person to transfer from a wheelchair to a vehicle seat?
Section 37.165(e) of the DOT ADA regulations allows persons who use wheelchairs to transfer to a vehicle seat, if one is available....
-
ASME: ADA Standard Section 105.2.2
Section 105.2.2 of the ADA Standards cover references to the American Society of Mechanical Engineers (ASME) standards.
-
5.1 Transfer Surface Height
5.1 Transfer Surface Height
-
3.13(b) Dispersed Wheelchair Locations in Auditoria with More Than 300 Seats
Dispersed Wheelchair Locations in Auditoria with More Than 300 Seats In all auditoria with more than 300 seats, wheelchair spaces shall be provided in more than one location....
