The Committee recommends exam chairs with a fixed footrest have a transfer surface minimum of a 17 inch depth and a 21 inch width located on both sides of the chair to allow for a left or...
Search Results "Dining Surface"
Filters
Commonly Searched Documents
-
5.3.3.1 Transfer Sides Recommendation for Exam Chairs with Fixed Footrests
-
Humanscale Float Height-Adjustable Table
Float is a revolutionary standing office desk that brings effortless operation to traditional sit-stand products. Ease of use is at the heart of Float, as it seamlessly adjusts...
-
Electrolux Icon 36" Freestanding Full-Gas Range
FEATURES: Smooth-Glide Oven Racks Ball bearing oven racks glide with unparalled ease and extend fully for effortless access. Flexible Cooktop Configuration The cooktop...
-
GPK Modular QuadDesk
Assistive Technology for People With Quadriplegia The Modular QuadDesk is different from any other desk on the market in that it was designed from the ground up with you, the...
-
Diversified Woodcrafts Mobile Lab Station with flat top 4352KF
ADA Compatible Mobile Lab Perfect for the physically impaired or for classroom demos. Constructed of solid oak, hardwood and oak veneers with a chemical resistant, earth-friendly...
-
M301.2.1 Height
The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured from the floor to the top of the transfer surface....
-
Lynx Grills Inc. 36” Grill - 1 ProSear Burner & 2 Stainless Steel Burners (L600ADA)
Available in 30" and 36" freestanding cart sizes. 32" high cooking surface 8" toekick Adjustable side handle for less than a 42" reach Accessible side or rear mounted propane...
-
Diversified Woodcrafts Oak Table with Book Compartments 24x48
Warranty Made in the USA Manufactured with 2 book compartments measuring 14"W x 13-5/8"D x 3-7/8"H Minimal assembly required; legs need to be attached No Table Surface...
-
1.1.9 Horizontal gaps and vertical alignment
horizontal discontinuities and variations in vertical alignment such as at concrete joints, gaps, grade breaks, and at the interface of concrete with other materials or elements built into the surface...
-
Lynx Grills Inc. 36” Grill 1 ProSear Burner & 2 Stainless Steel Burners with Rotisserie (L600ADAR)
Available in 30" and 36" freestanding cart sizes. 32" high cooking surface 8" toekick Adjustable side handle for less than a 42" reach Accessible side or rear mounted propane...
-
Lynx Grills Inc. 30” Grill 1 ProSear Burner & 1 Stainless Steel Burner with Rotisserie (L500ADAR)
Available in 30" and 36" freestanding cart sizes. 32" high cooking surface 8" toekick Adjustable side handle for less than a 42" reach Accessible side or rear mounted propane...
-
Cross Slope
Cross Slope The cross slopes of gangways, transition plates and floating piers that are part of an accessible route must be designed and constructed not to exceed a maximum of 2...
-
Addendum D: Comparison of demographics and transfer height between Phase 1 and Phase 2 of the study
[See subsections ...]
-
4.3.7 Slope
An accessible route with a running slope greater than 1:20 is a ramp and shall comply with 4.8. Nowhere shall the cross slope of an accessible route exceed 1:50.
-
4.3.7 SLOPE
An accessible route with a running slope greater than 1:20 is a ramp and shall comply with 4.8. Nowhere shall the cross slope of an accessible route exceed 1:50.
-
Electronic instruments
Electronic instruments have been developed to measure floor flatness. Originally created to measure the flatness of concrete floors in critical applications such as narrow - aisle...
-
Circular Cross Section and Clearance (§505.5, §505.7)
Circular Cross Section and Clearance
-
T503.5 Exterior Illumination for Boarding and Alighting Areas
Exterior lighting shall be provided to illuminate walking surfaces of boarding and alighting areas when the doors of non-rail vehicles are open....
-
Ronick Matting Systems BaseMat 300 Entrance Floor Mat
At 3/8" depth this aluminum entrance floor mat is suited for a wide range of applications ranging from surface mounted to recessed installations....
-
Wheeled Mobility Anthropometry Project
The data and recommendations from the Wheeled Mobility Anthropometry Project are discussed in connection with the following technical criteria: • Height of transfer surfaces on diagnostic...
-
5.4.2.2 Transfer and Positioning Support Length for Imaging Equipment with Transfer Surfaces
5.4.2.2 Transfer and Positioning Support Length for Imaging Equipment with Transfer Surfaces....
-
M305.3.2.1 Horizontal Position
The height of the top of the gripping surface on horizontal standing supports shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....
-
M302.2.5 Unobstructed Transfer
Each transfer side complying with M302.2.4 shall provide unobstructed access to transfer surfaces. EXCEPTIONS: 1....
-
Implication for Standards and Design
The station used in this second phase permitted greater freedom of wheelchair positioning around the transfer surface compared to the first phase station. ...
