The transition from station platform to the ramp or bridge plate and the transition from car floor to the ramp or bridge plate may be vertical without edge treatment up to 1⁄4 inch....
Search Results "Push Plate"
Filters
Commonly Searched Documents
-
§ 38.125(c)(3) Ramp threshold
-
§ 38.95(c)(3) Ramp threshold
The transition from station platform to the ramp or bridge plate and the transition from car floor to the ramp or bridge plate may be vertical without edge treatment up to 1/4 inch....
-
T503.2 Ramps and Bridgeplates
When ramps or bridgeplates are deployed, the walking surface shall be lighted with 2 foot-candles (22 lux) minimum of illumination.
-
T402.10 Visual Contrast
The perimeter of the walking surface on ramps and bridgeplates shall be marked by a stripe. The stripe shall be 1 inch (25 mm) wide minimum and shall contrast visually with the rest...
-
§ 38.95(c)(6) Attachment
(6) Attachment—.
-
Hager Companies Push/Pull Latch 311H
Hager Push/Pull Latch 311H: - New design replacing 311D - Engraving is available (optional) - Non-handed - Hospital latch Standard Materials: - Zinc and stainless...
-
Hager Companies Push/Pull Latch 311L
Hager Push/Pull Latch 311L: - Engraving available (optional) - Lead lined - Non-handed - Hospital Latch - 311L is same as 311H but for use on lead lined doors - *Horizontal...
-
Rockwood Manufacturing Company 107 x 73B/73BL Concealed Mount Pull Plate 8" CTC Pull 3-1/2" x 15" Plate
Stud welded lugs on the back of the push plate are permanently attached to the 1/8" thick push plate. Cone Head MS attached to selected door pull....
-
Boat Slips: ADA Standard Section 1003.2.1
Where gangways connect to transition plates, landings specified by 405.7 shall not be required. 6....
-
11B-1003.2.1 Boat slips
Where gangways connect to transition plates, landings specified by Section 11B-405.7 shall not be required....
-
4.31.3* MOUNTING HEIGHT
The highest operable part of the telephone shall be within the reach ranges specified in 4.2.5 or 4.2.6.
-
§ 38.95(c)(2) Ramp surface
The ramp or bridge plate surface shall be continuous and slip resistant, shall not have protrusions from the surface greater than 1/4 inch high, shall have a clear width of 30 inches and...
-
Figure 404.2.4.1(f) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Push Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(j) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Push Side – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(g) Maneuvering Clearances at Manual Swinging Doors and Gates: Hinge Approach, Push Side with Closer and Latch – Drawing from the U.S. Access Board
-
Allegion Glynn-Johnson Push/Pull Latches
Glynn-Johnson manufactures a full line of push/pull latches, including the standard passage set, a privacy set and a version that incorporates a mortise lock....
-
Cross Slope
Cross Slope The cross slopes of gangways, transition plates and floating piers that are part of an accessible route must be designed and constructed to not exceed a maximum of 2 percent...
-
T402.5 Surfaces
Ramp and bridgeplate surface material shall comply with T302 and extend across the full width and length of the ramp or bridgeplate.
-
§ 38.125(c)(6) Attachment
(6) Attachment—
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
EZ Dock Transition Plate
Our gangway transition plate with ThruFlowTM decking creates a sturdy transition between the shore grade and aluminum gangway. Available in three widths: 3’, 4’, and 5’....
-
T402.12 Stowage
Where portable ramps and bridgeplates are permitted, a compartment, securement system, or other storage method shall be provided within the non-rail vehicle to stow such ramps and...
-
T402 Ramps and Bridgeplates
The technical requirements for ramps and bridgeplates in the 2016 Non-Rail Vehicle Guidelines include provisions on design load, installation and operation, emergency operation,...
-
Do reach range requirements apply to elements or only to operable parts of elements?
Reach range requirements apply to the operable portions of elements, including handles, controls, switches, buttons, control pads and other mechanisms that must be activated or...
