If the State Historic Preservation Officer or Advisory Council on Historic Preservation agrees that compliance with the requirements for accessible routes (exterior and interior), ramps,...
Search Results "Perpendicular Curb Ramp"
-
4.1.7(2)(a)(ii) ADA Application
-
T502.2.1 Over-the-Road Buses
For over-the-road buses, the vertical clearance at doorways shall be 65 inches (1650 mm) minimum.
- SafetyStepTD Ramp-Up Detectable Warning System
-
§27.75(a)(2) Curb cuts.
(2) Curb cuts....
-
3) Where the standard says "Changes in level are not permitted", but no advisory follows the standard
305.2, 405.4, and 802.1.1 Does it apply in similar sections that also say "changes in level are not permitted" but are not described/listed in the advisory at 304.2, such as 405.7.1 at ramp...
-
2. Standing Supports
The Committee recommended that for single-ramped entry raised platforms with wheelchair spaces, the standing supports located on two sides of the platform have a minimum of 34 inches between...
-
H. Your Obligation to Provide Services and Equipment
[Sec. 382.39(a)] More specifically, you must provide, as needed, the following: services personnel ground wheelchairs boarding wheelchairs ramps or mechanical...
-
Can accessible spaces be parallel instead of perpendicular?
The Standards do not specifically require that accessible spaces be perpendicular instead of parallel, but perpendicular parking spaces are preferred at facilities located on sites because...
- Accessible Pittsburgh: The One Step Project
- PlayLSI: A Higher Level of Inclusive Play
- Retail Store Disability Access; Dawn Secret Treasures: BigBell
-
1023.9 Stairway identification signs
A sign shall be provided at each floor landing in an interior exit stairway and ramp connecting more than three stories designating the floor level, the terminus of the top and bottom of...
-
10.3.2(2)
(2) The accessible route required by 10.3.2(1) shall include the features specified in 10.3.1(1), (4)-(9), (11)-(15), and (17)-(19).
-
Circular Cross Section and Clearance (§505.5, §505.7)
Circular Cross Section and Clearance (§505.5, §505.7)
- EZ Launch for Kayaks and Canoes with Accessible Transfer Bench
-
Ramp
Ramp: A ramped surface was designed to insert between two steps and serve as an integrated sliding board to assist with the transfers by bridging the gap between steps. ...
-
5.8.1.2 Entry to Wheelchair Spaces on Raised Platforms
5.8.1.2 Entry to Wheelchair Spaces on Raised Platforms.
-
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height. Edge protection is not required on platforms 1 ½ inches or less in height.
-
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height Recommendations
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height Recommendations The Committee recommends that no edge protection be required on platforms of 1½ inches or less...
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)
-
§ 37.42(f)
vertical gap is more than 5/8 inch, measured when the vehicle is at rest, the horizontal and vertical gaps between the car floor and the boarding platform must be mitigated by a bridge plate, ramp...
-
DSA Drawing 11B-406.6-8 Cut-Through Median with No Gutters (2016 CBC)
Requires the Premium User plan or above. (Login or upgrade your account!)
-
Handrail extension requirements
Just concurring with Brian's comments. Most concise demonstration of how to (correctly) measure handrail extension length I've come across. No more arguing with Architects...will...
