(f) Hold and release of accessible seating....
Search Results "L-Shaped Seat"
Commonly Searched Documents
-
§ 35.138(f) Hold and release of accessible seating
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2.
-
11B-233.3.1.2.6.5 Additional requirements.
Water closet seat height complying with Section 11B-809.10.7.4. 7. Electrical receptacles, switches and controls complying with Section 11B-809.12. 8....
- Kohler C3® 200 Elongated Bidet Toilet Seat With In-line Heater and Remote Control Video
-
12. Seating, tables, or work surfaces
Seating, tables, or work surfaces 4.30 If provided in accessible spaces, at least one of each type provided....
-
T213.3 Armrests at Aisle Seats on Over-the-Road Buses
Where armrests are provided on the aisle side of seats on over-the-road buses, folding or removable armrests shall be provided on the aisle side of at least 50 percent of aisle seats....
-
HOW TO MEASURE TRANSFER HEIGHTS IS IMPORTANT
HOW TO MEASURE TRANSFER HEIGHTS IS IMPORTANT Many medical examination rooms are equipped with fixed height examination tables, with a typical 32-inch seat height....
-
David L Munson, IALD Aff.
Introduction I didn’t graduate from medical school but I have learned a couple of lessons. One I’ve learned is that I’m going to get older; I’m going to have vision problems;...
- GameTime Adaptive Swing Seat
-
Identification of available accessible seating. (Section-by-Section Analysis)
Section 36.302(f)(3) of the proposed rule requires a facility to identify available accessible seating. ...
-
FEATURES
FEATURES Several necessary features determine the shape of an examination table seat: The perineal cut-out provides access to the perineum for gynecological and urological examinations...
-
11B-221.2.1.1 General seating
TABLE 11B-221.2.1.1 NUMBER OF WHEELCHAIR SPACES IN ASSEMBLY AREAS NUMBER OF SEATS MINIMUM NUMBER OF REQUIRED WHEELCHAIR SPACES...
-
11B-221.2.1.1 General seating
TABLE 11B-221.2.1.1 NUMBER OF WHEELCHAIR SPACES IN ASSEMBLY AREAS Number Of Seats Minimum Number Of Required Wheelchair Spaces 4 to 25 1...
-
11B-221.2.1.1 General seating
TABLE 11B-221.2.1.1 NUMBER OF WHEELCHAIR SPACES IN ASSEMBLY AREAS NUMBER OF SEATS MINIMUM NUMBER OF REQUIRED WHEELCHAIR SPACES...
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer.
-
M305.2.7 Clearance
Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...
-
5.4.10 Transfer Support Fittings Recommendations for M301 and M302
5.4.10 Transfer Support Fittings Recommendations for M301 and M302 Description: To ensure safe and effective transfers, transfer supports must not rotate within their fittings...
-
Height – M301.2.1 & M302.2.1
Height – M301.2.1 & M302.2.1 The subcommittee discussed the increments for adjustability and decided that infinite adjustability is the appropriate standard as both electronic...
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings.
-
§ 36.302(f)(4) Notification of accessible seating locations
(4) Notification of accessible seating locations. ...
-
APPENDIX E - SEATING PLANS FOR MODIFIED THEATERS
APPENDIX E SEATING PLANS FOR MODIFIED THEATERS...
-
Team or player seating areas. (Section-by-Section Analysis)
Section 221.2.1.4 of the 2004 ADAAG requires one or more wheelchair spaces to be provided in each team or player seating area with fixed seats, depending upon the number of seats provided...
-
Section 36.308 Seating in Assembly Areas (Section-by-Section Analysis)
Section 36.308(a)(1)(ii)(A) and (B) have been revised to provide that wheelchair and companion seats must be an integral part of the seating area, dispersed to all accessible seating levels...