[ECTCR UFAS 4.21.6, 4.34.5.5(5)] EXCEPTION: A fixed shower head located at 48 inches (1220 mm) maximum above the shower finish floor shall be permitted instead of a hand-held spray unit...
Search Results "Finished Grade"
-
608.6 Shower Spray Unit and Water
-
308.3.2 Obstructed High Reach
The top of washing machines and clothes dryers shall be permitted to be 36 inches (915 mm) maximum above the finish floor. 2....
-
Suggestion by Eldon Tipping
Slopes were to be measured with a Dipstick Floor Profiler (Face Construction Technologies) within 16 hours after completion of final finishing, and where applicable, before removal of any...
-
11B-805.6 Hand washing fixtures, lavatories and sinks
to Section 11B-306.3.3, Exception 1 which states: "At lavatories required to be accessible by Section 11B-213.3.4, the knee clearance shall be 27 inches (686 mm) high minimum above the finish...
-
Standards
the different types of deviations and tolerances used for specifications Other international standards: Australian NATSPEC Reference Volume 1: Building Works, Concrete Finishes...
-
Sloped Surfaces
The amount of slope or grade is described as the proportion of a vertical rise to a horizontal length....
-
BACKGROUND
are deaf, alleged that JCMC personnel failed to provide effective communication with them during the times that their adult daughter, Sydnei Cantrell, was being treated at JCMC for high-grade...
-
Introduction and Instructions
These questions are not meant to be graded, but rather to be used as a planning tools to help identify opportunities for improvements, set priorities, and to track improvements over time...
-
RESULTS OF OBJECTIVE SURFACE MEASUREMENT
., 8.3% grade for 30 feet)....
-
Design Speed
Development of Bicycle Facilities (p. 36) specifies 30 km/h (20 mi/h) as the minimum design speed that should be used on shared use paths (figure 47).(2) It goes on to provide modifiers for grades...
-
Attachment A
Description Initial Scope of Project Required Accessibility Work 6.3D New on-grade parking lot with PV system as part of larger project or as a separate concurrent...
-
Hager Companies 3600 Series Lever
Hager 3600 Series Grade 2 tubular lockset provides the necessary security and dependability of a commercial lock with a more residential look....
-
Yale 3000 Series Architectural Door Closer
This U.L. listed, ANSI Grade 1 closer has a long history of proven quality. ...
-
Behavioral Safety Products #DH410 Cylindrical Ligature Resistant Lever Handle
The escutcheon and lever handle is constructed of solid stainless steel, and is being offered in a satin stainless steel finish. ...
-
DORMA 9000 Series Exit Device
Available Finishes The 9000 Series is available in architectural finishes as well as powder coated finishes....
-
Cal-Royal Products Swing Clear Hinges
A 316 grade stainless steel or clear coat over 304L is recommended. Stainless steel can also be polished to a satin or bright finish....
-
BEST Door Lever Hardware Cylindrical Locks - 7KC
Features: Versatile trims & finishes available. Cylindrical chassis to fit common door preparation. Standard and Drive-in latches available....
-
Corbin Russwin Inc. BLSS Trim Lever Handle & Lockset
Units Patient Room Doors De-escalation Rooms Psychiatric Facilities Assisted Living Facilities Features: Overlapping lever and rose construction Uses the ANSI/BHMA Grade...
-
Cal-Royal Epic 800 Series Cylindrical Leverset
ANSI STANDARDS - Meets or exceeds requirements of BHMA/ANSI A156.2 Series 4000, Grade 3....
-
Sargent 7 Line Lever Lock
Best overall lock in the Grade 2 class....
-
TownSteel CDC-110 Classroom Instruder Mechanical Cylindrical
The CDC-110 is ANSI/BHMA A156.3-2011 certified grade 1 and UL 10C 3-hour rated....
-
11B-308.3.2 Obstructed high reach
The top of washing machines and clothes dryers shall be permitted to be 36 inches (914 mm) maximum above the finish floor. 2. ...
-
Updates and Other Pocket Guides
We are currently finishing additional Pocket Guide versions covering selected state access standards. ...
-
11B-703.7.2.6 Toilet and bathing facilities geometric symbols
The symbol shall be mounted at 58 inches (1473 mm) minimum and 60 inches (1524 mm) maximum above the finish floor or ground surface measured from the centerline of the symbol....
