Where fewer than one parking space is provided for each residential dwelling unit, parking spaces complying with Section 11B-502 shall be provided in accordance with Table 11B-208.2....
Search Results "Built-In Table"
Filters
Commonly Searched Documents
-
11B-208.2.3.1 Parking for residents
-
11B-407.4.7.2 Keypads
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 11B-703.3.1....
-
Garaventa Artira Inclined Platform Wheelchair Lift
In restaurants, for example, the dedicated space required for a vertical platform lift can instead be used for an additional table....
-
Landscape Forms Inc. Multiplicity Bench Collection
The bench is a perfect companion to the MultipliCITY table under which it efficiently slides....
-
Safe Harbor
There is an exception for existing pools, wading pools, and spas built before March 15, 2012 [See § 36.304(g)(5)] Note: Noncomplying newly constructed and altered elements may also be...
-
Safe Harbors
There is an exception for existing pools, wading pools, and spas built before March 15, 2012....
-
3. Exception to Ramp Running Slope
The Committee reviewed and discussed the provisions on slopes for ramps as they apply to architectural elements in the built environment....
-
Customer Premises Equipment (Section-by-Section Analysis)
The guidelines do not differentiate between hardware, firmware or software implementations of a product's functions or features, nor do they differentiate between functions and features built...
-
Introduction
Tasks that are performed on the table, like rolling over, need to be accommodated....
-
4.3.5.3 180-degree turn around an obstacle
The bold dashed line in the table and figure indicates the current ADA requirements, which vary based on the passage width and space available at the base of the turn....
-
Door King Inc. 1520/1524 Stand Alone Card Readers
The 1520 is available with a built-in proximity card reader (DK Prox, AWID or HID) or can be ordered as a single door controller allowing the user to add their own 26-bit access control...
-
11B-221.2.1.3 Other boxes
In boxes other than those required to comply with Section 11B-221.2.1.2, the total number of wheelchair spaces required shall be determined in accordance with Table 11B-221.2.1.1....
-
Evaluation of transfers
Our results also showed that in terms of minimum space required for the transfer, the guidelines are insufficient (Table 12)....
-
Baseline
The cost estimates prepared by the Volpe Center are summarized in the table below, along with questions in the preamble to the proposed guidelines that seek additional information to refine...
-
11B-306.3.3 Minimum required depth
the finish floor or ground at a depth of 8 inches (203 mm) minimum increasing to 29 inches (737 mm) high minimum above the finish floor or ground at the front edge of a counter with a built-in...
-
Accessible Swimming Pools and Spas
ADAAG addresses only the built environment (structures and grounds); the guidelines do not address operational issues....
-
Accessible Golf Courses
ADAAG addresses only the built environment (structures and grounds). The guidelines do not address operational issues....
-
New Construction
Public toilets at a park were built to comply with the new construction requirements of the ADA Standards....
-
602.2 Accessibility and Compatibility Features
Documentation shall include accessibility features that are built-in and accessibility features that provide compatibility with assistive technology....
-
III-3.12000 Places of public accommodation located in private residences
ILLUSTRATION: J, a family day care provider, is having a new home built. J intends to use two of the rooms as a family day care center....
-
1.1.1
ADAAG and accessibility experts recommend that ramps be built with the least slope possible but in no case should a ramp exceed a 1:12 slope (except for curb ramp flares, and other approved...
-
11B-306.3.3 Minimum required depth
the finish floor or ground at a depth of 8 inches (203 mm) minimum increasing to 29 inches (737 mm) high minimum above the finish floor or ground at the front edge of a counter with a built-in...
-
11B-306.3.3 Minimum required depth
the finish floor or ground at a depth of 8 inches (203 mm) minimum increasing to 29 inches (737 mm) high minimum above the finish floor or ground at the front edge of a counter with a built-in...
-
11B-407.4.7.2 Keypads
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 11B-703.3.1 _|Braille Dimensions|_....
