Section 35.151(e) Social service center establishments In the NPRM, the Department proposed a new Sec. 35.151(e) requiring group homes, halfway houses, shelters, or similar social...
Search Results "Bathtub Clearance"
-
Section 35.151(e) Social service center establishments
-
A4.17.5 Doors
To make it easier for wheelchair users to close toilet stall doors, doors can be provided with closers, spring hinges, or a pull bar mounted on the inside surface of the door near...
-
4.9.4 HANDRAILS
Stairways shall have handrails at both sides of all stairs. Handrails shall comply with 4.26 and shall have the following features: (1) Handrails shall be continuous along both...
-
A4.17.5 DOORS
To make it easier for wheelchair users to close toilet stall doors, doors can be provided with closers, spring hinges, or a pull bar mounted on the inside surface of the door near...
-
4.8.5* HANDRAILS
If a ramp run has a rise greater than 6 in (250 mm) or a horizontal projection greater than 72 in (1830 mm), then it shall have handrails on both sides. Handrails are not required on...
-
Handrails [§504.6, §505]
A vertical clearance 9” minimum between upper and lower handrails will help prevent entrapment....
-
4.34.5.5(1) Size and clearances
(1) Size and clearances. Shower stall size and clear floor space shall comply with either Fig. 35(a) or (b). The shower stall in Fig. 35(a) shall be 36 in by 36 in (915 mm by 915 mm)....
-
Bobrick Two-Wall Tub/Shower Toilet Compartment Grab Bar B-5837
36" W x 54" D (91 x 137cm), 1-1/4" (32mm) dia. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick Two-Wall Tub/Shower Toilet Compartment Grab Bar Peened B-68137.99
36" W x 54" D (91 x 137cm), 1-1/2" (38mm) dia., peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick Two-Wall Tub/Shower Toilet Compartment Grab Bar Peened B-5837.99
36" W x 54" D (91 x 137cm), 1-1/4" (32mm) dia., peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick Two-Wall Tub/Shower Toilet Compartment Grab Bar B-68137
36" W x 54" D (91 x 137cm), 1-1/2" (38mm) dia. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Parking
access aisles. 11B-502.4 Identification at accessible spaces and/or lot entrances. 11B-502.6 11B-502.8 Vertical clearance...
-
Parking
access aisles. 11B-502.4 Identification at accessible spaces and/or lot entrances. 11B-502.6 11B-502.8 Vertical clearance...
-
Delta 1-1/2″ x 42″ ADA Grab Bar Concealed Mounting 40142-SS
Product Features and Benefits 42″ long, 1 1/2″ wide Concealed mounting - mounting hardware included 3″ diameter flanges 1 1/2″ wall clearance Limited Faucet and Finish Warranty...
-
Hot water heaters and knee clearance
If the hot water has sharp or abrasive edges or if the piping serving the hot water heater falls within the required knee clearance.............
-
Van-Accessible Parking Spaces
spaces are the same as accessible parking spaces for cars except for three features needed for vans: a wider access aisle (96") to accommodate a wheelchair lift; vertical clearance...
-
Section B: Passenger Drop-Off Area
(§503.4) B3 Is there vertical clearance of at least 114" (9 feet 6 inches) from the site entrance to the vehicle pull-up area, in the access aisle...
-
11B-205.1 General
Operable parts on accessible elements, accessible routes, and in accessible rooms and spaces shall comply with Section 11B-309. Exceptions: 1. Operable parts that are...
-
F205.1 General
Operable parts on accessible elements, accessible routes, and in accessible rooms and spaces shall comply with 309. EXCEPTIONS: 1. Operable parts that are intended for use only by...
-
23.1 Q. What type of reinforcement should be used to reinforce bathroom walls for the later installation of grab bars?
A. The Guidelines do not prescribe the type of material to use or method of providing reinforcement for bathroom walls. The Guidelines recognize that grab bar reinforcing may be...
-
7(2)(a)(ii)
(ii) Clear floor space is provided at fixtures as shown in Fig. 7 (a), (b), (c) and (d). Clear floor space at fixtures may overlap. Fig. 7 Clear Floor Space for...
-
24.1 Q. What types of grab bars should the reinforcement be designed to accommodate and what types may be used if the builder elects to install grab bars in some units at the time of construction?
A. The Guidelines do not prescribe the type of product for grab bars, or the structural strength for grab bars. The Guidelines only state that the necessary reinforcement must be...
-
11B-205.1 General
Operable parts on accessible elements, accessible routes, and in accessible rooms and spaces shall comply with Section 11B-309. Exceptions: 1. Operable parts that are intended...
-
205.1 General
Operable parts on accessible elements, accessible routes, and in accessible rooms and spaces shall comply with 309. EXCEPTIONS: 1. Operable parts that are intended for use...
