5.4.10 Transfer Support Fittings Recommendations for M301 and M302 Description: To ensure safe and effective transfers, transfer supports must not rotate within their fittings during...
Search Results "Transfer Seat (Transportation)"
-
5.4.10 Transfer Support Fittings Recommendations for M301 and M302
-
A4.1.3(19)(a)
Folding seating units are usually two fixed seats that can be easily folded into a fixed center bar to allow for one or two open spaces for wheelchair users when necessary....
-
Space Needs
Table 11 shows that for a given width of 40 inches (centered in front of the transfer station) that 25% of the subjects were able to perform a transfer to the platform in Protocol A (no...
-
5.3.2 Transfer Sides Recommendations for M301
5.3.2 Transfer Sides Recommendations for M301 Description: The transfer side provision requires the transfer surface to be located to provide options to transfer onto the short side and...
-
M303 Diagnostic Equipment Used by Patients Seated in Wheelchair
M303 provides technical criteria for diagnostic equipment used by patients seated in a wheelchair....
-
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment On imaging equipment, the transfer surface is oriented along the long dimension of the surface where...
-
4.32.1 Minimum Number
Fixed or built-in seating or tables required to be accessible by 4.1 shall comply with 4.32....
-
1008.3.2.2 Height
Each transfer step shall be 8 inches (205 mm) high maximum....
-
1008.3.2.2 Height
Each transfer step shall be 8 inches (205 mm) high maximum....
-
11B-1008.3.2.2 Height
Each transfer step shall be 8 inches (203 mm) high maximum....
-
11B-1008.3.2.2 Height
Each transfer step shall be 8 inches (203 mm) high maximum....
-
11B-1008.3.2.2 Height
Each transfer step shall be 8 inches (203 mm) high maximum....
-
810.5.3 Platform and Vehicle Floor Coordination
In light rail, commuter rail, and intercity rail systems subject to Department of Transportation regulation 49 CFR 37.21 where it is not operationally or structurally feasible to meet the...
-
T603 Wheelchair Securement Systems
[See subsections ...]
-
§ 37.42(e)
(e) In any situation using a combination of high and low platforms, a commuter or intercity rail operator shall not employ a solution that has the effect of channeling passengers...
-
§ 37.42(e)
(e) In any situation using a combination of high and low platforms, a commuter or intercity rail operator shall not employ a solution that has the effect of channeling passengers...
-
Fixed or Built-in Seating and Tables [4.32]
[See subsections ...]
-
A4.32 SEATING, TABLES, AND WORK SURFACES
[See subsections ...]
-
4.32.1 MINIMUM NUMBER
Fixed or built-in seating, tables, or work surfaces required to be accessible by 4.1 shall comply with 4.32....
-
§304(a) General Rule
No individual shall be discriminated against on the basis of disability in the full and equal enjoyment of specified public transportation services provided by a private entity that is primarily...
-
1008.3.2.2 Height
Each transfer step shall be 8 inches (205 mm) high maximum....
-
Security
Similar to the situation involving FAA safety requirements, part 382 is consistent with security requirements mandated by the Transportation Security Administration (TSA)....
-
Participants
Further demographic details of the study can be seen in Table 3, including hours using a wheelchair per day, years using a wheelchair, number of level and non-level transfers and average...
-
Section 36.308 Seating in Assembly Areas (Preamble, Section-by-Section Analysis)
In order to facilitate seating of wheelchair users who wish to transfer to existing seating, paragraph (a)(1) of the final rule adds a requirement that, to the extent readily achievable,...