Openings [§302.3] Openings in ground and floor surfaces, such as grates, are limited in width to prevent passage of a ½” diameter sphere....
Search Results "Transfer Surface Height"
Filters
Commonly Searched Documents
-
Openings [§302.3]
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved.
-
Shredded Rubber
The surface material used as a play safety surface has gained some popularity as a means to reuse tires. ...
-
1014.3.2 Slope
The slope of the floor surface shall not be steeper than 1:48 in any direction....
-
1014.3.2 Slope
The slope of the floor surface shall not be steeper than 1:48 in any direction....
-
Non Slip Safety Solutions
The end result is a floor surface engineered for lasting beauty and trouble-free maintenance....
-
Handrail Requirements
The proposed rule specified that gripping surfaces be continuous and unobstructed by elements, including newel posts (505.6)....
-
A4.16.4 Grab Bars
A6(a) and (b) show the diagonal and side approaches most commonly used to transfer from a wheelchair to a water closet....
-
A4.16.4 GRAB BARS
A5(a) and (b) show the diagonal and side approaches most commonly used to transfer from a wheelchair to a water closet....
-
Scoping [4.1.2(4), 4.1.3(3)]
Requirements in 4.5 apply to accessible routes and spaces, including ramps, elevators, platform lifts, and clear floor space. These requirements apply to interior and exterior...
-
Cross Slope: ADA Standard Section 405.3
Section 405.3 covers the current ADA Standards for cross slope requirements on ramps.
-
504.2 Treads and Risers
All steps on a flight of stairs shall have uniform riser heights and uniform tread depths. Risers shall be 4 inches (100 mm) high minimum and 7 inches (180 mm) high maximum....
-
Aluminum Heavy Duty Wheels n' Heels® Metro Grating
Metro has an even greater strength to weight ratio, and much improved aesthetic appeal, since there are now no welds on the top surface....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3....
-
302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (13 mm) diameter except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10....
-
302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (13 mm) diameter except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10....
-
5.4.10 Transfer Support Fittings for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.10 Transfer Support Fittings for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
504.2 Treads and Risers
All steps on a flight of stairs shall have uniform riser heights and uniform tread depths. Risers shall be 4 inches (100 mm) high minimum and 7 inches (180 mm) high maximum....
-
504.2 Treads and Risers
All steps on a flight of stairs shall have uniform riser heights and uniform tread depths. Risers shall be 4 inches (100 mm) high minimum and 7 inches (180 mm) high maximum....
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
11B-1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (864 mm) maximum above the ground or deck surface....
-
ADA Tolerances - Related Industry Standards
[See subsections ...]
