Existing elevators shall not be required to comply with 407.2.2.2....
Search Results "Elevator Car Position Indicator"
Filters
Commonly Searched Documents
-
11B-407.2.2.2 Visible signals
-
11B-407.2.2.2 Visible signals
Existing elevators shall not be required to comply with 407.2.2.2....
-
M302.3.1 Transfer Supports (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed that transfer supports must be provided for use with transfer sides on diagnostic equipment used by patients in the seated position, and that these...
-
M301.2.2 Sunset Provision (Section-by-Section Analysis)
As discussed in Section IV.B.1.a. (Significant Changes – Transfer Surface Adjustability), this is a new provision that was added to the final rule in conjunction with the new...
-
Figure M5: Overview of M303 Diagnostic Equipment for Use by a Patient While Seated in a Wheelchair and 304 Diagnostic Equipment for Use by a Patient in a Standing Position (Mammography Machine Example)
Where the primary use of the equipment supports more than one patient position, it must comply with the requirements for each use. ...
-
1006.3.1 Clear Width
The clear width of golf car passages shall be 48 inches (1220 mm) minimum....
-
M305 Supports
[See subsections ...]
-
M305 Supports (Section-by-Section Analysis)
M305 in the final rule provides the technical requirements for transfer supports, standing supports, leg supports, and head and back supports. Transfer supports are required for...
-
M305 Supports
[See subsections ...]
-
Elevated Accessible Routes
Elevated Accessible Routes An elevated accessible route is the path used for connecting elevated play components. ...
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
409.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
11B-407.2.2.2 Visible signals
Existing elevators shall not be required to comply with 407.2.2.2 FIGURE 11B-407.2.2.2 ‡‡ VISIBLE HALL SIGNALS...
-
§ 38.125(c)(6) Attachment
(6) Attachment—
-
§ 38.125(c)(1) Design load
(1) Design load. Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26...
-
§ 38.125(c)(7) Stowage
(7) Stowage. A compartment, securement system, or other appropriate method shall be provided to ensure that stowed ramps or bridge plates, including portable ramps or bridge plates...
-
§ 38.125(b)(3) Emergency operation
(3) Emergency operation. The lift shall incorporate an emergency method of deploying, lowering to ground or station platform level with a lift occupant, and raising and stowing the...
-
§ 38.125(b)(1) Design load
(1) Design load. The design load of the lift shall be at least 600 pounds. Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which the lift...
-
§ 38.91(c)(1)
(1) Commuter rail cars shall comply with §§38.93(d) and 38.109 of this part for level boarding unless structurally or operationally impracticable....
-
Shower Spray Unit and Water: ADA Standard Section 607.6
Section 607.5 covers the current ADA Standards for bathtub shower spray units and the water temperature of the spray units.
-
11B-607.6 Shower spray unit and water
A shower spray unit with a hose 59 inches (1499 mm) long minimum that can be used both as a fixed-position shower head and as a hand-held shower shall be provided....
-
408 Limited-Use/Limited-Application Elevators
408 Limited-Use/Limited-Application Elevators...