LiveEquipd’s mission is to fill the void that exists for people looking for equipment and supplies to manage their disabilities through our integrated platform....
Search Results "Platform Edge"
Commonly Searched Documents
- LiveEquipd
-
Level boarding bus system
A system in which buses operate where some or all of the designated stops have boarding platforms and the design of boarding platforms and non-rail vehicles are coordinated to provide boarding...
-
Cross Slope
The percentage of rise to length, which is the difference in elevation, when measuring the trail tread from edge to edge perpendicular to the direction of travel This may be expressed as...
-
Poll Worker Training
The materials must clarify that the Edge machines are the method of private and independent voting chosen by the Supervisor....
-
11B-809.7.2 Changes in level
Ramps complying with Section 11B-405, elevators complying with Section 11B-407 or platform lifts complying with Section 11B-410 shall be provided where changes in level exceed 1/2 inch (...
-
Vertical Clearance: ADA Standard Section 307.4
Section 307.4 covers the current ADA Standards for vertical clearance.
-
11B-307.4 Vertical clearance
The leading edge of such guardrail or barrier shall be located 27 inches (686 mm) maximum above the finish floor or ground....
-
Side guard protocol
Then the height of the platform was adjusted incrementally in height: higher and lower than the subject’s seat and the maximum transfer heights high/low that were attainable were recorded...
-
Transit Shelters (R308.2) (Section-by-Section Analysis)
Transit Shelters (R308.2) (Section-by-Section Analysis) Transit shelters must be connected by a pedestrian access route to boarding and alighting areas or boarding platforms....
-
11B-302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (12.7 mm) diameter except as allowed in Sections 11B-407.4.3 _|Platform to Hoistway Clearance|_,...
-
502.2.2 No Disruption of Accessibility Features
Software shall not disrupt platform features that are defined in the platform documentation as accessibility features....
-
502.2.2 No Disruption of Accessibility Features
Applications shall not disrupt platform features that are defined in the platform documentation as accessibility features....
-
1009.2.2 Seat Location
In the raised position, the centerline of the seat shall be located over the deck and 16 inches (405 mm) minimum from the edge of the pool....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with Section 11B-303....
-
FIGURE INDEX
Maneuvering Clearances at Recessed Doors and Gates Figure 404.2.6 Doors in Series and Gates in Series Figure 405.7 Ramp Landings Figure 405.9.1 Extended Floor or Ground Surface Edge...
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
502.2 Documented Accessibility Features
Software with platform features defined in platform documentation as accessibility features shall conform to 502.2....
-
11B-1009.2.2 Seat location
In the raised position, the centerline of the seat shall be located over the deck and 16 inches (406 mm) minimum from the edge of the pool....
-
603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1015 mm) maximum above the finish floor or ground....
-
603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1015 mm) maximum above the finish floor or ground....
-
5.4.4.1 Transfer Support Distance from Transfer Surface Recommendation for Stretchers
The horizontal distance from transfer surface should be no more than 3 inches from the edge of the patient support surface....
-
11B-603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1016 mm) maximum above the finish floor or ground....
-
603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1015 mm) maximum above the finish floor or ground....
-
603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1015 mm) maximum above the finish floor or ground....