equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured vertically to the floor or grade below at any point within 36 inches (914 mm) horizontally...
Search Results "Horizontal Standing Support"
-
1015.2 Where required
-
Re: Tax Information for People with Disabilities A Complete and Simple Guide
A well-written evaluation essay demonstrates your ability to assess a subject objectively and support your conclusions academically....
-
11B-604.8.1.4 Toe clearance
provide a toe clearance of 9 inches (229 mm) minimum above the finish floor and 6 inches (152 mm) deep minimum beyond the compartment-side face of the partition, exclusive of partition support...
-
11B-604.8.1.4 Toe clearance
provide a toe clearance of 9 inches (229 mm) minimum above the finish floor and 6 inches (152 mm) deep minimum beyond the compartment-side face of the partition, exclusive of partition support...
-
Window Ease
Window Ease™ attaches to any manufactured single-hung, double-hung or horizontal sliding window....
-
Southwest Home Products Window Ease Latching System
Modifies New or Existing Windows For Vertical or Horizontal Sliding Windows Compliance with All Codes Guaranteed Window EaseTM is not a window....
-
504.2.1 Preservation of Accessibility Information in Format Conversion (Section-by-Section Analysis)
Analysis) This section proposes that authoring tools, when converting content or saving content in multiple formats, must preserve information required for accessibility to the extent supported...
-
Stress Management
Provide praise and positive reinforcement Refer to EAP Allow employee to make telephone calls for support Provide sensitivity training for workforce Allow the presence and use of...
-
4.28.3(7)
(7) In general, no place in any room or space required to have a visual signal appliance shall be more than 50 ft (15 m) from the signal (in the horizontal plane)....
-
4.9.4(2)
At the bottom, the handrail shall continue to slope for a distance of the width of one tread from the bottom riser; the remainder of the extension shall be horizontal (see Fig. 19(c) and...
-
§ 38.53(d)(1) Requirements
Where new vehicles will operate in new stations, the design of vehicles shall be coordinated with the boarding platform design such that the horizontal gap between each vehicle door at rest...
-
§ 38.173(b)
(b) Where the vehicle covered by paragraph (a) will operate in an accessible station, the design of vehicles shall be coordinated with the boarding platform design such that the horizontal...
-
11B-216.4.1 Exit doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
§382.27(c)(8)
(8) Transportation of an emotional support or psychiatric service animal in the cabin;...
-
seca 684 r Digital Multifunctional Scale with Integrated RS232 Interface
Product Properties Safe weighing of standing, sitting or wheelchair patients. Large, easy-to-access platform. Wheel barrier provides extra safety....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
4. Wheelchair seat depth
Wheelchair seat depth For this study, wheelchair seat depth was calculated as the horizontal distance from the proximal (i.e., towards the rear) edge to the distal (i.e., towards the...
-
2.2 Lighting Conditions
On each trial one measurement of horizontal illuminance was manually recorded from a Minolta T-1 Illuminance meter....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
