There are several methods that can be used for measuring slopes and cross slopes with a digital slope meter. Each method has advantages and disadvantages.
Search Results "Ground Floor Exit"
Filters
Commonly Searched Documents
-
Methods for Placing a Slope Tool on the Surface
-
1007.2 Continuity and components
1007.2 Continuity and components. Each required accessible means of egress shall be continuous to a public way and shall consist of one or more of the following components:
-
1009.2 Continuity and components
Each required accessible means of egress shall be continuous to a public way and shall consist of one or more of the following components:
-
Door Swing: ADA Standard Section 304.4
Section 304.4 covers the current ADA Standards for doors swinging into turning spaces.
-
206 Accessible Routes
At least one must be a ground floor entrance. Public entrances are any entrances that are not loading or service entrances....
-
Figure 11B-407.2.3.1 Floor designation
SECTION TITLE NOTES Figure 11B-407.2.3.1 Floor designation....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with Section 11B-303....
-
2. a. ii. Accessible entrance and exit route
[See subsections ...]
-
1132A.5.1 General
The floor or landing on the dwelling unit side of the primary entry door and any required exit door shall have a minimum length of not less than 44 inches (1118 mm)....
-
1015.6 Slope
The slope of the surface of clear ground spaces and turning spaces shall not be steeper than 1:48 in any direction....
-
1015.6 Slope
The slope of the surface of clear ground spaces and turning spaces shall not be steeper than 1:48 in any direction....
-
11B-411.4.11.1 Height
Floor destination characters shall be 1 inch (25 mm) high minimum complying with Section 11B-703.5.3....
-
11B-411.4.11.1 Height
Floor destination characters shall be 1 inch (25 mm) high minimum complying with Section 11B-703.5.3....
-
11B-411.4.11.1 Height
Floor destination characters shall be 1 inch (25 mm) high minimum complying with Section 11B-703.5.3....
-
Figure 810.3 Bus Shelters – Drawing from the U.S. Access Board
-
11B-411.4.6.2 Buttons
The car shall not have non-functional, exposed floor buttons....
-
11B-411.4.6.2 Buttons
The car shall not have non-functional, exposed floor buttons....
-
11B-411.4.6.2 Buttons
The car shall not have non-functional, exposed floor buttons....
-
Areas of Refuge [IBC §1007.6 (2003), §1003.2.13.5 (2000)]
They must provide direct access to an exit stairway (or to an elevator equipped with standby power). Horizontal exits can substitute for areas of refuge....
-
306.2.3 Minimum Required Depth
Where toe clearance is required at an element as part of a clear floor space, the toe clearance shall extend 17 inches (430 mm) minimum under the element....
-
306.2.3 Minimum Required Depth
Where toe clearance is required at an element as part of a clear floor space, the toe clearance shall extend 17 inches (430 mm) minimum under the element....
-
306.2.3 Minimum Required Depth
Where toe clearance is required at an element as part of a clear floor space, the toe clearance shall extend 17 inches (430 mm) minimum under the element....
