The high forward reach shall be 48 inches (1220 mm) maximum where the reach depth is 20 inches (510 mm) maximum....
Search Results "Expected Maximum Flight Duration"
-
308.2.2 Obstructed High Reach
-
11B-812.9 Surface marking
The centerline of the text shall be a maximum of 6 inches (152 mm) from the centerline of the vehicle space and its lower corner at, or lower side aligned with, the end of the vehicle space...
-
11B-812.9 Surface marking
The centerline of the text shall be a maximum of 6 inches (152 mm) from the centerline of the vehicle space and its lower corner at, or lower side aligned with, the end of the vehicle space...
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
11B-608.6 Shower spray unit and water
Shower spray units shall deliver water that is 120°F (49°C) maximum....
-
11B-608.6 Shower spray unit and water
Shower spray units shall deliver water that is 120°F (49°C) maximum....
-
11B-809.8.3.1 Floor or ground surface
., concrete, brick, flagstone) may have a maximum change in height from the interior landing of 4 inches (102 mm)....
-
Voting Area
If voters are expected to vote at counters or tables, there should be a writing surface that provides knee and toe clearance so that a voter who uses a wheelchair may sit at and use the...
-
Executive Order 12866
Although the benefits and costs are difficult to quantify, the rule is expected to have a positive economic impact....
-
Q3.) What are the types of “manufacturing processes” that were anticipated where the advisory says “tolerances recognized by this provision include… “those that may be a necessary consequence of a particular manufacturing process”?
To simplify the tolerance assessment, the 2010 Standards specify that the shower compartment be measured at the center points of opposing sides but the expectation is that the width at the...
-
2.5.2.2 International Organization for Standardization (ISO) Standards
Risk management plays a critical and central role in the design of medical devices, and it also ties into IEC 60601-1 and FDA’s expectations for quality systems and premarket clearance or...
-
Physical Barriers
How long will the driver wait for you if your visit runs over the expected time?...
-
A.2.ii. - Should EIT be compatible with assistive technology?
Also, multimedia presentations that require captioning and descriptive video must have these features built into the product, as it is impractical to expect end users to add on their own...
-
Scoping of residential dwelling units for sale to individual owners. (Section-by-Section Analysis)
The Department expects that, after consultation and coordination with HUD, the Department will make a determination in the final rule....
-
Minimum Clear Headroom
This design specification was not expected to conflict with typical door heights....
-
H29
[ADA Standards § 4.25.3] Yes No Note: For many emergency shelters, evacuees are not expected to use shower or bathing facilities due to the short period they may stay at the...
-
Q. What are the limitations on the obligation to make a reasonable accommodation?
In general, a larger employer would be expected to make accommodations requiring greater effort or expense than would be required of a smaller employer....
-
Surface [1017.2]
A stable trail surface is not permanently affected by expected weather conditions and can sustain normal wear and tear from the expected uses between planned maintenances....
-
11B-703.8.4 Character height
Exception: In assembly seating where the maximum viewing distance is 100 feet (30.5 m) or greater, the height of the uppercase “I” of low resolution VMS fonts shall be permitted to be 1...
-
11B-703.8.4 Character height
Exception: In assembly seating where the maximum viewing distance is 100 feet (30.5 m) or greater, the height of the uppercase “I” of low resolution VMS fonts shall be permitted to be 1...
-
11B-703.8.4 Character height
Exception: In assembly seating where the maximum viewing distance is 100 feet (30.5 m) or greater, the height of the uppercase “I” of low resolution VMS fonts shall be permitted to be 1...
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....