Each car shall be equipped with a self-leveling feature that will automatically bring and maintain the car at floor landings within a tolerance of 1/2 inch (13 mm) under rated loading to...
Search Results "Tolerance"
Filters
Commonly Searched Documents
-
407.4.4 Leveling
-
Automatic Operation [4.10.2]
Self-leveling must correct the overtravel or undertravel of a car as it stops at a landing within a ½ inch vertical tolerance since changes in level greater than ½ inch can be troublesome...
-
Calculation of Percentages
For dimensions not expressed as an absolute (“X maximum” or “Y minimum”), specify in a manner that accommodates the expected tolerance within the required dimensions by subtracting the tolerance...
-
1.1.1
The dimension should be determined by the expected tolerance of the construction element....
-
10 - foot straightedge method
The 10 - foot straightedge method has been a standard in ACI - 117, Standard Tolerances for Concrete Construction, for many years and is optional as part of ACI 117....
-
35. Must an employer withhold discipline or termination of an employee who, because of a disability, violated a conduct rule that is job-related for the position in question and consistent with business necessity?
This means, for example, that an employer never has to tolerate or excuse violence, threats of violence, stealing, or destruction of property....
-
4.10.2 Automatic Operation
Each car shall be equipped with a self-leveling feature that will automatically bring the car to floor landings within a tolerance of 1/2 in (13 mm) under rated loading to zero loading conditions...
-
4.10.2 AUTOMATIC OPERATION
Each car shall be equipped with a self-leveling feature that will automatically bring the car to floor landings within a tolerance of 1/2 in (13 mm) under rated loading to zero loading conditions...
-
The Time Has Come
Our message to America is that inequality and prejudice will no longer be tolerated. Our message to people with disabilities is that your time has come. Senator Robert Dole9 9....
-
Accessibility - Flatness and Lippage
A subsurface tolerance of 1/8" in 10’ may be required....
-
The Shameful Wall
Once again, we rejoice as this barrier falls, proclaiming together we will not accept, we will not excuse, we will not tolerate discrimination in America. . . ....
-
2. New Construction and Alterations
They also failed to properly take into account dimensional tolerances and their impact on the variation. Cherry v....
-
17. What should employers do to prevent and correct harassment?
Employers should make clear that they will not tolerate harassment based on disability or on any other basis....
-
Bobrick TrimLineSeries™ Recessed Napkin/Tampon Vendor 25₵, 50₵ and Free Operation B-37063
The unit follows the Universal Design principle for “tolerance for error” by automatically blocking the coin slot with a red indicator when the machine is empty, and by allowing the wrong...
-
Car Dimensions: ADA Standard Section 407.4.1
Section 407.4.1 covers the current ADA Standards for elevator car dimensions.
-
604.2 Location
ETA Editor’s Note: The 1991 ADA Standards allowed construction tolerances from an 18” absolute dimension. ...
-
709.5 Openings
The doors shall be close fitting within operational tolerances, and shall not have undercuts, louvers or grilles....
-
What would happen with other disability groups?
However, generally children can also tolerate higher levels of energy expenditure, and therefore higher levels of energy consumption do not necessarily relate to a lack of accessibility....
-
Horizontal Alignment
As shown in table 19, users of manual wheelchairs tolerated the lowest degree of lateral acceleration, "coefficients of friction."...
-
SDC Sure Exit® PSB560 REX Pressure Sense Exit Bar
for unequalled safety and reliability Human touch not required, ensuring superior safety release for the frail, disabled and wheelchair compatible Sensor calibration not required Tolerates...
-
3. FIELD VERIFICATION
check process. 3.2 During Construction: Path of travel items within the scope of the project represented as code compliant but found to be nonconforming beyond reasonable construction tolerances...
-
604.2 Location
ETA Editor’s Note: The prior standards allowed construction tolerances to occur on either side of an 18” absolute dimension....
-
Maintaining Concentration
Maintaining Concentration: Individuals with ASD may experience decreased concentration and may not be able to tolerate distractions such as office traffic, employee chatter, and common...
-
Aluminum Swaged SG Series Pressure-Locked Grating
Because of its aesthetic appeal and the ability to meet tight tolerances, this product is often used for architectural applications....
