Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions. Question 5....
Search Results "Tolerance"
Filters
Commonly Searched Documents
-
M101.5 Dimensional Tolerances
-
5. CONSTRUCTION TOLERANCES
CONSTRUCTION TOLERANCES: While it is always advisable to avoid design requirements that are at or near dimensional thresholds, construction tolerances may be used when evaluating the compliance...
-
R103.1 Conventional Industry Tolerances
R103.1 Conventional Industry Tolerances. Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
Dimensional Tolerances [3.2]
ADAAG recognizes conventional industry tolerances for field conditions. This applies to the field work, not the design work....
-
§ 38.4(b) Dimensional tolerances
(b) Dimensional tolerances....
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range with specific minimum or maximum end points....
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range with specific minimum or maximum end points....
-
Construction and Manufacturing Tolerances: ADA Standard Section 104.1.1
Section 104.1.1 of the ADA Standards covers the most current information on dimensions in regards to construction and manufacturing tolerances in the ADA Standards.
-
Construction and Manufacturing Tolerances
A tolerance is an unintended, but permitted (i.e., “tolerated”), variation from a specified dimension resulting from the process of construction or manufacture....
-
11B-104.1.1 Construction and manufacturing tolerances
Advisory 11B-104.1.1 Construction and manufacturing tolerances. ...
-
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis)
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis) This section would provide that dimensions are subject to conventional industry tolerances except where dimensions...
-
C101.3 Conventional Industry Tolerances (Section-by-Section Analysis)
C101.3 Conventional Industry Tolerances (Section-by-Section Analysis) This proposed section, which has a parallel provision in the proposed 508 Standards (E101.3), would provide that...
-
3.2 Dimensional Tolerances
All dimensions are subject to conventional building industry tolerances for field conditions....
-
3.2 DIMENSIONAL TOLERANCES
All dimensions are subject to conventional building industry tolerances for field conditions....
-
Q2.) What are the types of “field conditions” that were anticipated where the advisory says “tolerances recognized by this provision include those for field conditions”?
Tolerances are not an “oops factor” for careless or sloppy design. ...
-
Q3.) What are the types of “manufacturing processes” that were anticipated where the advisory says “tolerances recognized by this provision include… “those that may be a necessary consequence of a particular manufacturing process”?
To simplify the tolerance assessment, the 2010 Standards specify that the shower compartment be measured at the center points of opposing sides but the expectation is that the width at the...
-
M101.6 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions....
-
M101.5 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions...
-
M101.6 Dimensional Tolerances (Section-by-Section Analysis)
The MDE NPRM proposed that dimensions were to be subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions....
-
104 Conventions
A commenter stated that the 2010 Standards restrict the application of construction tolerances only to those few requirements that are expressed as an absolute dimension....
-
Industry Standards
fit ISO 3443-4 Building construction—Tolerances for building—Part 4: Methods for predicting deviation of assemblies and the distribution of tolerances ISO 3443...
-
Background
Many trade groups have developed standard tolerances for certain aspects of construction....