At least 5 percent, but no fewer than one, of practice putting greens, practice teeing grounds, and teeing stations at driving ranges shall be designed and constructed so that a golf car...
Search Results "Range Hood"
Filters
Commonly Searched Documents
-
11B-238.3 Practice putting greens, practice teeing grounds, and teeing stations at driving ranges
-
11B-238.3 Practice putting greens, practice teeing grounds, and teeing stations at driving ranges
At least 5 percent, but no fewer than one, of practice putting greens, practice teeing grounds, and teeing stations at driving ranges shall be designed and constructed so that a golf car...
-
11B-238.3 Practice putting greens, practice teeing grounds, and teeing stations at driving ranges
At least 5 percent, but no fewer than one, of practice putting greens, practice teeing grounds, and teeing stations at driving ranges shall be designed and constructed so that a golf car...
-
407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in 308, measured to the centerline of the highest operable part....
-
407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in 308, measured to the centerline of the highest operable part....
-
T304.2 Height
Operable parts shall be located 24 inches (610 mm) minimum and 48 inches (1220 mm) maximum above the floor of non-rail vehicles.
-
407.8.1 Vertical Reference Plane
Operable parts shall be positioned for a side reach or a forward reach determined with respect to a vertical reference plane. The vertical reference plane shall be located in...
-
407.12.1 Vertical Reference Plane (Section-by-Section Analysis)
407.12.1 Vertical Reference Plane (Section-by-Section Analysis) This section proposes that the positioning of operable parts for side reaches and forward reaches be determined...
-
407.12.1 Vertical Reference Plane
Operable parts shall be positioned for a side reach or a forward reach determined with respect to a vertical reference plane. The vertical reference plane shall be located in...
-
407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in 308, measured to the centerline of the highest operable part....
-
Do reach range requirements apply to elements or only to operable parts of elements?
Reach range requirements apply to the operable portions of elements, including handles, controls, switches, buttons, control pads and other mechanisms that must be activated or manipulated...
-
4.3.6 Reach Limits
Horizontal distances in the positive range represent offset distance away from the body (or barrier depth) when reaching over an obstruction in relation to the forward-most point, and the...
-
Height [4.27.3]
Height [4.27.3] The operable portions of controls and operating mechanisms must be within established reach ranges for either a forward or side reach as required in 4.2.5 and 4.2.6 (see...
-
4.3 Reach Ranges
4.3 Reach Ranges Figures 14-15 and Table 4 show the standards from the four countries related to reach from a wheeled mobility device....
-
Unobstructed: ADA Standard Section 308.3.1
Section 308.3.1 covers the current ADA Standards for unobstructed side reach.
-
11B-308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1219 mm) maximum and the low...
-
Self Contained, Closed Products - Side Reach Range
Requires the Accessibility Specialist plan or above. (Login or upgrade your account!)
-
1007.3.2 Golf Club Reach Range Area
1007.3.2 Golf Club Reach Range Area....
-
11B-104.1.1 Construction and manufacturing tolerances
Where the requirement states a specified range, such as in 609.4 where grab bars must be installed between 33 inches and 36 inches above the floor, the range provides an adequate tolerance...
-
11B-104.1.1 Construction and manufacturing tolerances
Where the requirement states a specified range, such as in 609.4 where grab bars must be installed between 33 inches and 36 inches above the floor, the range provides an adequate tolerance...
-
11B-104.1.1 Construction and manufacturing tolerances
Where the requirement states a specified range, such as in Section 11B-609.4 where grab bars must be installed between 33 inches and 36 inches above the floor, the range provides an adequate...
-
F104.1.1 Construction and Manufacturing Tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
104.1.1 Construction and Manufacturing Tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
104.1.1 Construction and Manufacturing Tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....