R406.3 Unobstructed Side Reach....
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
R406.3 Unobstructed Side Reach
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
-
Obstructed High Reach: ADA Standard Section 308.3.2
Section 308.3.2 covers the current ADA Standards for obstructed high side reach.
-
Doorways: ADA Standard Section 405.7.5
Section 405.7.5 covers the current ADA Standards for doorway maneuvering clearance at ramp landings.
-
11B-306.3.5 Width
Knee clearance shall be 30 inches (762 mm) wide minimum....
-
11B-306.2.5 Width
Toe clearance shall be 30 inches (762 mm) wide minimum....
-
4.7.5 SIDES OF CURB RAMPS
If a curb ramp is located where pedestrians must walk across the ramp, or where it is not protected by handrails or guardrails, then it shall have flared sides; the maximum slope of the...
-
Doorways without Doors or Gates, Sliding Doors, and Folding Doors: ADA Standard Section 404.2.4.2
Section 404.2.4.2 covers the current ADA Standards for maneuvering clearances at doorways without doors or gates, sliding doors, and folding doors.
-
11B-404.2.4.2 Doorways without doors or gates, sliding doors, and folding doors
Approach direction Perpendicular to doorway Parallel to doorway (beyond stop/latch side unless noted) From Front 48...
-
11B-306.3.2 Maximum depth
Knee clearance shall extend 25 inches (635 mm) maximum under an element at 9 inches (229 mm) above the finish floor or ground....
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1ΒΌ inch (32 mm) maximum....
-
11B-306.2.1 General
Space under an element between the finish floor or ground and 9 inches (229 mm) above the finish floor or ground shall be considered toe clearance and shall comply with Section 11B-306.2...
-
11B-804.2 Clearance
Where a pass through kitchen is provided, clearances shall comply with Section 11B-804.2.1. Where a U-shaped kitchen is provided, clearances shall comply with Section 11B-804.2.2....
-
Sides of Curb Ramps [4.7.5]
Where pedestrians cross the ramp, curb ramps are required to have side flares; sharp returns present tripping hazards....
-
R304.2.3 Flared Sides
R304.2.3 Flared Sides. Where a pedestrian circulation path crosses the curb ramp, flared sides shall be sloped 10 percent maximum, measured parallel to the curb line....
-
Knee Clearance: Clearance as Measured from Distal Knee Point - Manual Wheelchair
This depicts knee and toe clearance required by manual chair users for forward approach to elements in the built environment (e.g., lavatories, drinking fountains)....
-
R405 Knee and Toe Clearance
R405 Knee and Toe Clearance...
-
306 Knee and Toe Clearance
306 Knee and Toe Clearance...
-
Knee Clearance: Clearance as Measured from Anterior-Most Point - Manual Wheelchair
This depicts knee and toe clearance required by manual chair users for forward approach to elements in the built environment (e.g., light switches)....
-
Knee Clearance: Clearance as Measured from Dorsal Foot Point - Manual Wheelchair
This depicts knee and toe clearance required by manual chair users for forward approach to elements in the built environment (e.g., countertops)....
-
4.7.5 Sides of Curb Ramps
If a curb ramp is located where pedestrians must walk across the ramp, or where it is not protected by handrails or guardrails, it shall have flared sides; the maximum slope of the flare...
-
11B-604.5.1 Side wall
The side wall grab bar shall be 42 inches (1067 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1372 mm) minimum from the rear wall with...
-
305.4 Knee and Toe Clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....