Number 1604 Ansi L13042 Shelf pack 10 Finishes 605, 606, 613, 625,...
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
Don-Jo Mfg., Inc. Door Flip Guards 1604
-
TownSteel TDG129 Door Guard
TDG129 Door Guard is made from zinc alloy. It is provided with projected lock ball and flip guard swing bar not allowing forced entry when...
-
Don-Jo Mfg., Inc. Door Flip Guards 1603
Number 1603 Ansi L33042 Shelf pack 10 Finishes 605, 606, 613, 625,...
-
11B-406.2.2 Sides of curb ramps
FIGURE 11B-406.2.2 ‡‡ SIDES OF CURB RAMPS...
-
11B-306.3 Knee clearance
[See subsections ...]
-
11B-306.2 Toe clearance
[See subsections ...]
-
11B-305.4 Knee and toe clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with Section 11B-306....
-
11B-604.8.1.2 Doors
A door pull complying with Section 11B-404.2.7 shall be placed on both sides of the door near the latch....
-
11B-604.8.1.1.2 Maneuvering space with side-opening door
In a wheelchair accessible compartment with a door located in the side wall or partition, either in-swinging or out-swinging, a minimum 60 inches (1524 mm) wide and 60 inches (1524 mm) deep...
-
Maneuvering Clearances at Doors [4.13.6]
Maneuvering Clearances at Doors [4.13.6] Pull-side clearance beyond the door swing provides space for a forward reach to door hardware....
-
11B-604.8.1.4 Toe clearance
At least one side partition shall provide a toe clearance of 9 inches (229 mm) minimum above the finish floor and 6 inches (152 mm) deep minimum beyond the compartment-side face of the partition...
-
4.13.6 MANEUVERING CLEARANCES AT DOORS
The floor or ground area within the required clearances shall be level and clear....
-
406.3 Sides of Curb Ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
-
4.13.6 Maneuvering Clearances at Doors
Minimum maneuvering clearances at doors that are not automatic or power-assisted shall be as shown in Fig. 25....
-
Rockwood Manufacturing Company 604 Door Guard - Solid Cast Brass
Material: Solid Cast Brass Options: 1/8" clear plastic shim - order separately as 604 SHIM. Fastener: Body: 3 ea. #6 x 1-1/2 OH SMS Strike: 4 ea. #6 x 3/4 OH...
-
Rockwood Manufacturing Company 603 Door Guard - Cast Aluminum
Material: Cast Aluminum Options: 1/8" clear plastic shim - order separately as 603 SHIM. Fastener: Body: 3 ea. #6 x 1-1/2 FH SMS Strike: 4 ea. #6 x 1 FH...
-
4.3.4 Knee and Toe Clearances
Hence, to accommodate a particular percentage of users, the side profile of a design element (shown by dotted line) should not extend outside the corresponding shaded area....
-
11B-411.4.3 Platform to hoistway clearance
Platform to hoistway clearance shall comply with Section 11B-407.4.3....
-
Side Transfer Surface
A transfer surface located within the length of the examination surface that allows patient transfer on two opposing sides of the examination surface....
-
Maneuvering Clearances [§404.2.4]
Maneuvering Clearances [§404.2.4] Required maneuvering clearances provide space for opening and proceeding through doors, doorways, and gates using wheelchairs and other mobility aids...
-
R406.3 Unobstructed Side Reach
R406.3 Unobstructed Side Reach....
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
-
11B-306.3.4 Clearance reduction
Between 9 inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches...
