Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground. Mirrors shall be full length with a reflective...
Search Results "Fitting"
-
11B-803.6 Mirrors
-
11B-803.5 Coat hooks and shelves
Coat hooks provided within the room shall be located within one of the reach ranges specified in Section 11B-308. Shelves shall be 40 inches (1016 mm) minimum and 48 inches (1219 mm)...
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground. Mirrors shall be full length with a reflective...
-
1. Transfer Supports
located within reach of the transfer surface and not obstruct transfer, be capable of resisting vertical and horizontal forces of 250 pounds applied to all points, and not rotate in their fittings...
-
Is turning space required in all rooms and spaces?
Turning space is required in certain spaces, such as toilet and bathing facilities, dressing and fitting rooms, and transient lodging guest rooms....
-
M305.2.8 Fittings (Section-by-Section Analysis)
The MDE NPRM proposed to require that transfer supports not rotate in their fittings (proposed M305.2.3). Five commenters addressed this provision....
-
Clear Floor Space [4.35.2]
Clear Floor Space [4.35.2] Clear floor space is required for a parallel approach to the bench. Recommendations: Consider additional space on the narrow dimension to allow...
-
5.4.10 Transfer Support Fittings Recommendations for M301 and M302
5.4.10 Transfer Support Fittings Recommendations for M301 and M302 Description: To ensure safe and effective transfers, transfer supports must not rotate within their fittings during...
-
Grab Bars
Grab bars must be installed so they don't rotate within their fittings....
-
Doors [4.35.3]
Doors [4.35.3] The size of rooms is further determined by the location and swing of doors. Doors cannot swing into the turning space (as allowed in toilet and bathrooms because...
-
F222.1 General
Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with 803....
-
222.1 General
Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with 803....
-
11B-222.1 General
Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with Section 11B-803...
-
11B-222.1 General
Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with Section 11B-803...
-
11B-222.1 General
Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with Section 11B-803...
-
4.8.5* HANDRAILS
(7) Handrails shall not rotate within their fittings....
-
222.1 General
Where dressing rooms, fitting rooms, or locker rooms are provided, at least 5 percent, but no fewer than one, of each type of use in each cluster provided shall comply with 803....
-
4.9.4 HANDRAILS
(7) Handrails shall not rotate within their fittings....
-
803.2 Turning Space
Turning space complying with 304 shall be provided within the room.
-
11B-803.2 Turning space
Turning space complying with Section 11B-304 shall be provided within the room.
-
803.2 Turning Space
Turning space complying with 304 shall be provided within the room.
-
803.2 Turning Space
803.2 Turning Space. Turning space complying with 304 shall be provided within the room.
-
11B-803.2 Turning space
Turning space complying with Section 11B-304 shall be provided within the room.
-
11B-803.2 Turning space
Turning space complying with Section 11B-304 shall be provided within the room.