Where an agency provides support documentation or services for ICT, such documentation and services shall conform to the requirements in Chapter 6....
Search Results "Back Support"
Filters
Commonly Searched Documents
-
E208.1 General
-
11B-1008.3.2.3 Transfer supports
At least one means of support for transferring shall be provided. [2010 ADAS] Advisory 1008.3.2.3 Transfer Supports. ...
-
11B-1008.3.2.3 Transfer supports
At least one means of support for transferring shall be provided. [2010 ADAS] Advisory 1008.3.2.3 Transfer Supports....
-
11B-1008.3.2.3 Transfer supports
At least one means of support for transferring shall be provided. Advisory 11B-1008.3.2.3 Transfer supports....
-
11B-407.4.10.3 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the support rail, fastener, mounting device...
-
11B-407.4.10.3 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the support rail, fastener, mounting device...
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
2. Armrests Requirement
space as the transfer supports as described in the MDE NPRM....
-
11B-407.4.10.3 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the support rail, fastener, mounting device...
-
11B-1008.3.1.4 Transfer supports
At least one means of support for transferring shall be provided....
-
11B-1008.3.1.4 Transfer supports
At least one means of support for transferring shall be provided....
-
11B-1008.3.1.4 Transfer supports
At least one means of support for transferring shall be provided. FIGURE 11B-1008.3.1 TRANSFER PLATFORMS...
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3....
-
M302.3 Supports
Transfer supports, armrests, and reclining surfaces shall comply with M302.3....
-
§382.117(e)
(e) If a passenger seeks to travel with an animal that is used as an emotional support or psychiatric service animal, you are not required to accept the animal for transportation in the...
-
§1193.33(b)
(b) Manufacturers shall include in general product information the contact method for obtaining the information required by paragraph (a) of this section.
-
Figure M1: Overview of M301 Diagnostic Equipment for Use by a Patient in a Supine, Prone, or Side-Lying Position
[See subsections ...]
-
Closers
In addition, ADAAG requires that low-energy doors not open to back check faster than 3 seconds and require no more than 15 Ib, which is consistent with ANSI/BHMA A156.19....
-
M305 Supports (Section-by-Section Analysis)
M305 in the final rule provides the technical requirements for transfer supports, standing supports, leg supports, and head and back supports....