Section 604.2 covers the current ADA Standards for the mounting location of water closets.
Search Results "Absolute Dimension"
Filters
Commonly Searched Documents
-
Location: ADA Standard Section 604.2
-
11B-409.4.1 Inside dimensions of elevator cars
Elevator cars shall provide a clear floor space of 36 inches (914 mm) minimum by 48 inches (1219 mm) minimum and shall comply with Section 11B-305.
-
Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry
Access Board RE: Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry...
-
Parallel Grab Bars
The proposed rule, consistent with the original ADAAG, specified that the lower grab bar be located 9 inches absolute above the bathtub rim....
-
Graphic Conventions [3.1]
Dimensions in ADAAG and this manual are absolute unless noted as a maximum or minimum. ADAAG includes in text and figures the metric equivalent (in millimeters)....
-
2.2.2 Structural Anthropometry (i.e. Body and WhMD Dimensions)
Body and WhMD Dimensions) A three-dimensional (3-D) electromechanical probe (i.e....
-
Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment
Access Board RE: Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment...
-
5.8.2 Knee and Toe Clearance Under Breast Platform
The overall knee and toe space should be increased to a minimum of 28 inches deep, from the initially proposed 25 inch absolute dimension; increasing the knee clearance directly underneath...
-
810.2.2 Dimensions--Modification to 810.2.2 of Appendix D to 36 CFR Part 1191
810.2.2 Dimensions--Modification to 810.2.2 of Appendix D to 36 CFR Part 1191 Bus boarding and alighting areas shall provide a clear length of 96 inches (2440 mm), measured perpendicular...
-
2.3.3 Comparison of Dimensions with Standards and other Anthropometric Studies
Measurement Dimension Country & Standards Document Australia Canada* U.K....
-
408.4.1 Car Dimensions and Doors
Elevator cars shall provide a clear width 42 inches (1065 mm) minimum and a clear depth 54 inches (1370 mm) minimum. Car doors shall be positioned at the narrow ends of cars and...
-
Ambulatory Accessible Compartment
Ambulatory accessible compartments were specified to be 36 inches wide absolute in the proposed rule, consistent with the original ADAAG....
-
Calculation of Percentages
In the case of specifications for dimensions or sizes that involve percentages or ratios, rounding down for values less than one half is allowed....
-
Grohe America Allure Brilliant Faucet
Crisp planes, intriguing angles and cut-out details, Allure Brilliant illustrates the absolute precision that can only be achieved through years of experience and an unfaltering passion...
-
3. MINIMUMS, MAXIMUMS AND SPECIFYING AT THE LIMIT
MINIMUMS, MAXIMUMS AND SPECIFYING AT THE LIMIT: Where an element is to be installed at the minimum or maximum permitted dimension, such as "48 inches maximum", it is not good practice to...
-
409.4.1 Inside Dimensions of Elevator Cars
Elevator cars shall provide a clear floor space of 36 inches (915 mm) minimum by 48 inches (1220 mm) minimum and shall comply with 305.
-
409.4.1 Inside Dimensions of Elevator Cars
Elevator cars shall provide a clear floor space of 36 inches (915 mm) minimum by 48 inches (1220 mm) minimum and shall comply with 305.
-
2010 ADA Standards
It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
-
604.2 Location
ETA Editor’s Note: The 1991 ADA Standards allowed construction tolerances from an 18” absolute dimension. ...
-
Clear Floor Space [4.16.2]
to the left or the right of the required clear floor space doors cannot swing into the clear floor space required at any fixture the 18 inch water closet centerline is absolute...
-
Truncated Domes
In addition, this commenter recommended that the spacing between domes be revised from an absolute of 2.35 inches to a range of 1.6 to 2.35 inches. Response....
-
Shape and Diameter
The 1½ inch clearance between walls and handrails is an absolute dimension; it provides knuckle clearance while preventing entrapment of the arm for people who lean on rails with their forearm...
-
604.2 Location
ETA Editor’s Note: The prior standards allowed construction tolerances to occur on either side of an 18” absolute dimension....
