The deviation from slope or plane of formed surfaces over 10 feet (3 m) is ± 0.3% of length. This is approximately 3/8 inch in 10 feet (10 mm in 3 m)....
Search Results "Slope Meter"
Filters
Commonly Searched Documents
-
Suggested accessibility guidelines for exterior concrete surfaces
-
11 [§ 4.7.6]
Built-up curb ramps should have flared sides with a slope of 10 percent or less or have edge protection and handrails on the sides....
-
303.3 Beveled
Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory 303.3 Beveled....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
Accessible Routes
Accessible route requirements in ADAAG address width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level, doors, egress, and areas...
-
Comments from Individuals Who Are Blind or Have Low Vision (Section-by-Section Analysis)
member of the advisory committee that recommended the proposed guidelines, but filed a minority report recommending detectable warning surfaces should be required only on curb ramps with slopes...
-
Recommendations for Future Research
• Additional research would be required to determine the validity and repeatability of the Rotational Penetrometer measurements on surfaces with slopes greater than 5%....
-
Whitehall Mfg. WH2142T2 Ligature Resistant Toilet Top Supply On-Floor Wall Waste
To comply with Ligature-Resistant needs, an optional sloped top cover (box) with a Top Supply flush valve is available. This toilet is configured for a wall waste application....
-
Salsbury Industries See Through Metal Locker Six Tier Box Style 1 Wide
combination or key padlocks and electronic locks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Salsbury Industries See Through Metal Locker Six Tier Box Style Bridge 16 Box
padlocks and factory installed electronic locks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Salsbury Industries 66000 Series Six Tier Box Style 1 Wide Standard Metal Lockers
combination or key padlocks and electronic locks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Salsbury Industries See Through Metal Locker Six Tier Box Style 3 Wide
combination or key padlocks and electronic locks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Salsbury Industries 66016 Standard Metal Locker Six Tier Box Style Bridge 16 Box 18 Inches Deep
combination or key locks and combination or key padlocks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Salsbury Industries 66000 Series Six Tier Box Style 3 Wide Standard Metal Lockers
combination or key padlocks and electronic locks Salsbury Industries is an ISO 9001: 2008 certified company and has excelled in the field of manufacturing since 1936 Options Sloping...
-
Allegion Von Duprin 94/95 Series INPACT Recessed Exit Device
The sloped, die-cast metal endcaps provide added support, protecting the device and the door against the heaviest impact....
-
Ytterberg Scientific Inc. FloorPro® Floor Flatness Measurement Device
As the FloorPro® travels the survey line, many inclinometer slope readings are gathered over a 1" interval every 6", averaged and average saved as the 6" slope....
-
11B-303.3 Beveled
Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (12.7 mm) high maximum shall be beveled with a slope not steeper than 1:2. [2010 ADAS] Advisory 303.3 Beveled. ...
-
Thresholds at Doorways
The 1991 Standards and the 2010 Standards require raised thresholds that exceed ¼ inch in height to be beveled on each side with a slope not steeper than 1:2....
-
Clear Deck Space
Clear Deck Space Clear deck space of 60 by 60 inches minimum, with a slope of not more than 1:48, must be provided at the base of a transfer wall....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for the location, width (minimum of 36 inches), passing space,head room, surface, slope (maximum of 1:12 or 8.33%), changes in level...
-
4(2)
(2) In single-story dwelling units, changes in level within the dwelling unit with heights between 1/4 inch and 1/2 inch are beveled with a slope no greater than 1:2....
-
303.3 Beveled
Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory 303.3 Beveled....
-
A. Accessible Entrance
Accessible Entrance Having a way to get into the emergency shelter on a surface that is firm, stable, slip resistant, without steps or steep slopes, and wide enough for a person using...
-
Outdoor Conditions [4.8.8]
A slope up to 2% is allowed at landings for adequate drainage....
