Where handrails are provided along walking surfaces with running slopes not steeper than 1:20 they shall comply with Section 11B-505. [2010 ADAS] Advisory 403.6 Handrails....
Search Results "End Transfer Surface"
Filters
Commonly Searched Documents
-
11B-403.6 Handrails
-
7. Commit to Ongoing Maintenance of Accessible Playground Surfaces as a Responsibility of Ownership
This will require the surface material to be raked level, filled and compacted so that the clear ground space is level in all directions for a safe transfer onto and off the equipment....
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3....
-
Tile Tech Pavers® Stamp-Tech™ Series Pavers
Its irregular top surface was developed from actual sections of stone. By rotating the direction of the pavers during installation the natural effect is complete....
-
11B-813.2.1.2 Clearance
At both ends of adult changing tables, clearance shall be provided measuring 36 inches (914 mm) minimum wide and a minimum length as long as the table width plus the width of the side clearance...
-
11B-403.6 Handrails
Where handrails are provided along walking surfaces with running slopes not steeper than 1:20 they shall comply with Section 11B-505. Advisory 11B-403.6 Handrails....
-
503.4 Floor and Ground Surfaces
503.4 Floor and Ground Surfaces. Vehicle pull-up spaces and access aisles serving them shall comply with 302....
-
b. Positioning Supports
(Section-by-Section Analysis – M305.2), the MDE Advisory Committee made recommendations to add requirements for positioning supports on mammography equipment and imaging equipment with transfer...
-
Slope [1013.3]
When the surface of tent pads, tent platforms, and clear ground spaces is constructed of materials other than asphalt, concrete, or boards, the surface must be no steeper than 1:48 (2 percent...
-
Shower
Although not a transfer issue, lowered sidewalls were intended to facilitate assisted showering....
-
Clear Deck Space
Clear Deck Space Clear deck space of 60 by 60 inches minimum, with a slope of not more than 1:48, must be provided at the base of a transfer wall....
-
Handrails Requirement
The handrail requirements in section 505 address specifications for continuity, height, clearance, gripping surface, cross section, fittings, and extensions....
-
Other international standards
Australian NATSPEC Reference Volume 1: Building Works, Concrete Finishes Section Three classes of surface finish based on using a straightedge method of testing: Class A...
-
11B-502.4 Floor or ground surfaces
Advisory 11B-502.4 Floor or ground surfaces. Access aisles are required to be nearly level in all directions to provide a surface for wheelchair transfer to and from vehicles....
-
III. Results of the Study
Table 10 shows the surface materials recommended by region and surface composition....
-
408.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
408.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
606.5 Exposed Pipes and Surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks...
-
Observations and Results
After playing for several minutes on each surface, the children were asked to stand on the surface they preferred....
-
804.3 Kitchen Work Surface
In residential dwelling units required to comply with 809, at least one 30 inches (760 mm) wide minimum section of counter shall provide a kitchen work surface that complies with 804.3....
-
804.3 Kitchen Work Surface
In residential dwelling units required to comply with 809, at least one 30 inches (760 mm) wide minimum section of counter shall provide a kitchen work surface that complies with 804.3....
-
1.1.3
1.1.3 A maximum overall design running slope for exterior accessible surfaces (other than ramps), such as sidewalks, of 4% (approximately 1:25) is recommended....
-
Firmness
The degree of surface resistance to deformation, especially by indentation or the movement of objects (U.S. Access Board, 2007)....
