Turning space complying with Section 11B-304 shall be provided within the cell....
Search Results "Clear Deck Space"
Filters
Commonly Searched Documents
-
11B-807.2.1 Turning space
-
R203 Machinery Spaces (Section-by-Section Analysis)
R203 Machinery Spaces (Section-by-Section Analysis) Vaults, tunnels, and other spaces used by service personnel only are not required to comply with the proposed guidelines....
-
11B-806.2.6 Turning space
Turning space complying with Section 11B-304 shall be provided within the guest room....
-
11B-809.7.1 Width
The clear width for the accessible route shall be 36 inches (914 mm) minimum. Exception: The clear width shall be permitted to be reduced to 32 inches (813 mm) minimum at doors....
-
4.3.5.3 180-degree turn around an obstacle
In effect, this condition is a space bounded by three sides and requires a lot more space because WhMD users cannot cut the corner like they can with a wider aisle width (Figure 4‒6)....
-
802.1 Wheelchair Spaces
Wheelchair spaces shall comply with 802.1....
-
106.5.77 Wheelchair Space
Space for a single wheelchair and its occupant....
-
802.1 Wheelchair Spaces
Wheelchair spaces shall comply with 802.1....
-
Outdoor Constructed Features
The proposed rule based the size of the clear ground space at outdoor constructed features on the dimensions for clear floor or ground surfaces in 305.2 of the Architectural Barriers Act...
-
R302.3 Continuous Width
Clear width requirements are contained in R304.5.1 for curb ramps and blended transitions, and in R407.4 for ramps....
-
11B-206.7.2 Wheelchair spaces
Platform lifts shall be permitted to provide an accessible route to comply with the wheelchair space dispersion and line-of-sight requirements of Sections 11B-221 and 11B-802....
-
Openings, Width and Length of Wheelchair Space
Openings, Width and Length of Wheelchair Space Openings and the width and length of wheelchair spaces need to be considered in relation to each other....
-
Plan 5A: 13-Foot Wide Accessible Guest Room
The following accessible features are provided in the bathroom: • Comparable vanity counter top space (section 806); • Transfer shower (section 603.2); • Shower seat (section 610.3...
-
Plan 2B: 13-Foot Wide Accessible Guest Room
The following accessible features are provided in the bathroom: • Comparable vanity counter top space (section 806); • Alternate roll-in type shower with folding seat is 36 inches...
-
11B-703.5.9 Line spacing
Spacing between the baselines of separate lines of characters within a message shall be 135 percent minimum and 170 percent maximum of the character height....
-
Accessible Parking Space Width
The proposed rule specified that car and van spaces be at least 8 feet wide and that access aisles be at least 5 feet wide for car spaces and at least 8 feet wide for van spaces....
-
106.5.63 Space
A definable area, such as a room, toilet room, hall, assembly area, entrance, storage room, alcove, courtyard, or lobby.
-
Turn Space
60-inch (1525mm) Diameter Space T-Shaped Space for 180 Degree Turns...
-
11B-703.8.8 Line spacing
Low resolution VMS characters shall comply with Section 11B-703.5.9.
-
Forward Approach
Forward Approach Knee and toe clearances specified for lavatories in 4.19, which recognize space for plumbing (see page 75), can be applied to sinks....
-
Sunlighten Community Solocarbon® Far Infrared Sauna
ultra low EMF for ultimate safety and are clinically tested to lower blood pressure, aid in detoxification and weight loss. 100% ADA-compliant with 36” door and 60”x60” turning space...
-
11B-604.8.1.1.2 Maneuvering space with side-opening door
accessible compartment with a door located in the side wall or partition, either in-swinging or out-swinging, a minimum 60 inches (1524 mm) wide and 60 inches (1524 mm) deep maneuvering space...
-
Tenant Spaces: ADA Standard Section 206.4.5
Section 206.4.5 covers scoping requirements in the most current ADA Standards for accessible routes to Ttenant spaces.
-
1017.2 Aisles in assembly spaces
1017.2 Aisles in assembly spaces. Aisles and aisle accessways serving a room or space used for assembly purposes shall comply with Section 1028....
