SAFE-STRIDE ACRYLIC Safe-Stride® is a specially formulated anti-slip safety paint, which contains grit to help provide a tough, sure-footed, and safer-traction surface Applied to cleaned...
Search Results "Work Surface"
-
Wooster Products Anti-Slip Safety Coatings Systems
-
3.3 Guidance on the Visual Properties of Detectable Warnings
Two relatively dark surfaces may provide high luminance contrast, but on asphalt or other dark sidewalk surfaces (with reflectance less than 10 percent) high contrast is not always a good...
-
11B-1008.2.6.2 Use zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition)....
-
11B-1008.2.6.2 Use zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition)....
-
11B-1008.2.6.2 Use zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition)....
-
How to Measure Transfer Surface Height
How to Measure Transfer Surface Height Regardless of the final decision on the low height measurement, the Subcommittee agreed that the height of the transfer surface would be measured...
-
Pilot Rock APTX Full Sized Pedestal Rectangular Utility Tables
These larger utility tables provide work or prep area for several people at the same time....
-
Tread
Tread—The portion of a trail, outdoor recreation access route, or beach access route where traffic moves (for pedestrian routes, this is the walking surface)....
-
§ 38.79(a)
(a) Floor surfaces on aisles, step treads, places for standees, and areas where wheelchair and mobility aid users are to be accommodated shall be slip-resistant....
-
Hologic, Inc.
Prone breast biopsy tables were considered by the “Imaging Equipment with Transfer Surfaces” sub-committee and are described in Section 4.3.2 of the full committee report....
-
1008.2.6.2 Use Zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
Resting Intervals [1016.8]
., as flat as possible) so that all the wheels of a mobility device touch the ground surface when turning into and out of the resting interval....
-
7.4.3.2 Cross Slope
Where the surface is paved or is elevated above the natural ground, the cross slope shall not be steeper than 1:48 (2 percent). ...
-
M305.2.5 Surface Hazards
Transfer supports and surfaces adjacent to transfer supports shall be free of sharp or abrasive components and shall have eased edges....
-
1008.2.6.2 Use Zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
1017.8.3 Slope
Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage....
-
1133A.1 General
Kitchens shall be on an accessible route and shall comply with this section. (See Figure 11A-10A.)
-
Handrails Along Walkways
Handrails Along Walkways. The 1991 Standards do not contain any technical requirement for handrails provided along walkways that are not ramps. Section 403.6 of the 2010 Standards...
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
Slope Ratio
Slope Ratio—A ratio of vertical distance to horizontal distance or rise to run.
-
2. Methodology
[See subsections ...]
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
1017.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage....
-
1017.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage....
