The amount of vertical distance that the seat was raised/lowered each time depended on the subject’s perceived and observed transfer abilities....
Search Results "Vertical Reference Plane"
-
Adjustable height protocol
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
Engineered vs. Outside
The seat values are of particular importance because vertical vibrations transferred through the seat of a seated individual are the most hazardous....
-
4.34.6.8* REFRIGERATOR/FREEZER
Provision shall be made for refrigerators which are: (1) Of the vertical side-by-side refrigerator/freezer type; or (2) Of the over-and-under type and meet the following requirements...
-
11B-1002.4.4 Clearances
Wheelchair spaces shall not be required to comply with Section 11B-307.4 _|Vertical Clearance|_. [2010 ADAS] Advisory 1002.4.4 Clearances Exception 3....
-
11B-303.3 Beveled
A change in level of ½ inch (13 mm) is permitted to be ¼ inch (6.4 mm) vertical plus ¼ inch (6.4 mm) beveled....
-
§ 38.159(b)(8) Platform entrance ramp
loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches (75 mm), and the transition from roadway or sidewalk to ramp may be vertical...
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
407.2.2.2 Visible Signals
The visible signal elements shall be 2 1/2 inches (64 mm) minimum measured along the vertical centerline of the element....
-
608.7 Thresholds
In transfer type shower compartments, thresholds 1/2 inch (13 mm) high maximum shall be beveled, rounded, or vertical....
-
504.4 Templates
Where templates are provided, templates allowing content creation that conforms to Level A and Level AA Success Criteria and Conformance Requirements in WCAG 2.0 (incorporated by reference...
-
216.4.3 Directional Signs
Signs required by section 1003.2.13.6 of the International Building Code (2000 edition) or section 1007.7 of the International Building Code (2003 edition) (incorporated by reference, see...
-
4. Comparison of Proposed Technical Provisions Applicable to Shared Use Paths and AASHTO Guide
R302.7.1 Vertical Alignment....
-
1.16 Traditional, sloped-floor or traditional seating
1.16 "Traditional, sloped-floor" or "traditional seating" shall mean and refer to the section of an auditorium in which the seats are not affixed on risers, but are instead affixed to...
-
810.9 Escalators
Where provided, escalators shall comply with the sections 6.1.3.5.6 and 6.1.3.6.5 of ASME A17.1 (incorporated by reference, see "Referenced Standards" in Chapter 1) and shall have a clear...
-
F207.2 Platform Lifts
permitted by section 1003.2.13.4 of the International Building Code (2000 edition and 2001 Supplement) or section 1007.5 of the International Building Code (2003 edition) (incorporated by reference...
-
Key Operation
The most recent edition of the ASME standard, which the final rule references, does not contain a requirement for key operation....
-
Technical Memorandum TM 2013-17 Water Closet Clearance - Overlap
TM 2013-17 Water Closet Clearances - Overlap Effective Date: June 1, 2013 2012 TAS Reference: 604.3.2 Based on TAS 106.3 and the application of terms and definitions in...
-
Section 3. Fair Housing Act Design and Construction Requirements
A reprint of §100.205 was included to provide easy reference to (1) the Act's accessibility requirements, as codified by §100.205; and (2) the additional examples of methods of compliance...
-
12186(b) Other provisions
) Other provisions Not later than 1 year after July 26, 1990, the Attorney General shall issue regulations in an accessible format to carry out the provisions of this subchapter not referred...