Some comments from industry, including Matsushita Electric Corporation of America suggested that the definition of customer premises equipment be changed "to confine the applicability of...
Search Results "Industry Standard"
Filters
Commonly Searched Documents
-
Customer Premises Equipment (Section-by-Section Analysis)
-
5.1.1 Transfer Surface Height Adjustability Recommendation for M301 and M302
Industry experts noted that adjustability is readily available in many existing products....
-
Bonded Impact/cushioning Surfaces
Given that there is no industry, governmental, or association definition or standard for compacting EWF, we followed playground industry installation practices. Figure 1....
-
Vanity Counter Tops
Industry commenters considered this specification unduly restrictive while persons with disabilities considered it inadequate in ensuring equivalent access....
-
R302.7.1 Vertical Alignment
Surfaces should be designed, constructed, and maintained according to appropriate industry standards, specifications, and recommendations for best practice....
-
Toilet Room Doors
Sections 4.22.2 and 4.22.3 of the 1991 Standards and Section 603.2.3 of the 2010 Standards permit the doors of all toilet or bathing rooms with in-swinging doors to swing into the required...
-
2016 National ADA Symposium
Requires the Accessibility Specialist plan or above. (Login or upgrade your account!)
-
F104.1.1 Construction and Manufacturing Tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
5.9.1 Standing Supports Recommendation In Reference To Mammography Equipment
Industry representatives posited that if a patient has limitations or balance issues severe enough to need standing assistance, then the healthcare provider should position her in a seated...
-
Standing Supports [M305.2]
Industry representatives posited that if a patient has limitations or balance issues severe enough to need standing assistance, then the healthcare provider should position her in a seated...
-
LEGAL REQUIREMENTS
evacuation plans may nonetheless have to address emergency evacuation for employees with disabilities1 as a reasonable accommodation under Title I of the ADA.2 In addition, employers in certain industries...
-
Sections 35.108(d)(1)(i) and 36.105(d)(1)(i)—Broad Construction, Not a Demanding Standard
Sections 35.108(d)(1)(i) and 36.105(d)(1)(i)—Broad Construction, Not a Demanding Standard In accordance with Congress’s overarching directive to construe the term ‘‘disability’’ broadly...
-
Section 35.151(h) Medical Care Facilities (Section-by-Section Analysis)
The Department is proposing a new § 35.151(h) on medical care facilities, which now must comply with the applicable sections of the proposed standards. ...
-
TDI
consumers and encourage their involvement in the continuing struggle for accessibletelecommunications, media, and information technologies Provide technical assistance and consulting to industry...
-
Proline Drain: QuickDrainUSA - Tub to Shower Conversion
Learn how easy it can be to complete a standard tub to shower conversion in under an hour with the Quick Drain shower pan kits and accessories....
-
Individual Captioning Devices (Section-by-Section Analysis)
See table 219.3 in the 2010 ADA Standards for Accessible Design (2010 Standards).36 Adding a requirement for a particular number of individual captioning devices would be consistent with...
-
Section 35.151(g)(4)
The Department proposed this bright-line rule for two reasons: (1) The movie theater industry petitioned for such a rule; and (2) the Department has acquired expertise on the design of stadium...
-
2. Standing Supports
effectiveness for persons with disabilities; b) if there were any alternative technical criteria that would be appropriate; c) whether angled supports are effective; and d) whether there are industry...
-
Omnia Industries Inc. Exterior Modern Mortise Entrance Lever Lockset with Plates - Solid Brass No.12368
Exterior Modern Mortise Entrance Lever Lockset with Plates - Solid Brass Dimensions: 10-9/16" Overall Finishes: US3*, US10B, US15, US26, US26D Notes: *Not available with...
-
Omnia Industries Inc. Interior Modern Lever Latchset with Modern Round Rose - Solid Brass No.930MD
Interior Modern Lever Latchset with Modern Round Rose - Solid Brass Dimensions: 2-1/2" Projection x 4-3/4" Length Finishes: US3, US10B, US14, US15, US26, US26D, TB
-
Wikk Industries Inc. PART#BPS SM-INGR CLEAR (628) with I36-3 CLEAR (628)
6”X6”X42” Tall, Clear Anodized Aluminum (628), Surface mount with concealed mounting base, 1 prep for INGRESS’R® ADA switch, Removable Black ABS cap Shown on the bollard- I36-3...
-
Wikk Industries Inc. PART# BPS SM-ING48 DB (710) with I36-3 Clear (628)
6”X6”X48” Tall, Dark Bronze Anodized Aluminum (710), Surface mount with concealed mounting base, 2 Preps for INGRESS’R® and card reader, Removable Black ABS Cap. **Customer can...
-
Sargent 8200 Lever Lock
When it comes to strength and durability, SARGENT continues to set standards with the 8200 Mortise lock....
-
American Standard Right Width 1.28-1.6 gpf FloWise Right Height Elongated Flushometer Toilet Front View
