In addition, there were five sites surfaced with a combination PIP and EWF, and eight sites surfaced with a combination TIL and EWF. ...
Search Results "Work Surface"
-
Engineered Wood Fiber
-
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302 Description: Gripping surface hazards are sharp or abrasive elements that prevent an individual from sufficiently...
-
Cross Slope (R302.6) (Section-by-Section Analysis)
In exterior environments, a maximum cross slope of 2 percent is generally accepted as adequate to allow water to drain off paved walking surfaces....
-
1015.2.1 Glazing
Where the glazing provided does not meet the strength and attachment requirements of Section 1607.8, complying guards shall also be located along glazed sides of open-sided walking surfaces...
-
1013.2.1 Glazing
Where the glazing provided does not meet the strength and attachment requirements of Section 1607.8, complying guards shall also be located along glazed sides of open-sided walking surfaces...
- Figure 505.6 Horizontal Projections Below Gripping Surface – Drawing from the U.S. Access Board
-
(4) Adjustability: Method of Measurement
The MDE NPRM proposed that the measurement of the height of the transfer surface for both diagnostic equipment used in the supine, prone, or side-lying position and diagnostic equipment...
- Sears Brands, LLC Craftsman 10 in. Digital LaserTrac® Level
-
Pemko 193 Slip resistance
Hello ETA, I see that you can ask for slip resistance by adding a coating to the Pemko 193 plate. Any experience with this application? Is this a permanent slip resistance or...
- EZ Dock EZ TRAIL® Modular Walkway
- Beneficial Designs
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel....
-
7.2.2.1 Determining Impracticability
The surface is not firm and stable for a distance of 45 feet or more (14 m). Limiting Factor 3. ...
-
Light Rail Platform Slope
The Board has explicitly specified that rail platforms shall slope no more than 1:48 in any direction, consistent with cross slope provisions for walking surfaces in section 403....
- Access Board: Accessible Route Carpet
-
Non-Circular Cross Sections: ADA Standard Section 505.7.2
Section 505.7.2 covers the current ADA Standards for the non-circular cross section of handrail gripping surfaces.
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
- Wooster Products Anti-Slip Safety Coatings Systems
- Pilot Rock APTX Full Sized Pedestal Rectangular Utility Table Using Lumber
- Pilot Rock APTX Full Sized Pedestal Rectangular Utility Tables Using Recycled Plastic
-
Can stair treads and risers be perforated?
Stair treads must meet requirements for floor or ground surfaces which specify that surface openings not allow passage of a sphere more than ½ inch in diameter (§302.3)....