Some shared use paths may cross private land....
Search Results "Cross Slope"
2010 ADA Definition
Cross Slope: The slope that is perpendicular to the direction of travel (see running slope).
Filters
Commonly Searched Documents
-
Public Right-of-Way
-
Compliance requirements
requirements The proposed accessibility guidelines address the design, construction, and alteration of pedestrian facilities in the public right-of-way, including sidewalks, pedestrian street crossings...
-
R305.1.4 Size
At pedestrian at-grade rail crossings not located within a street or highway, detectable warnings shall extend the full width of the crossing....
-
11B-502.3 Access aisle
In parking facilities where the accessible route must cross vehicular traffic lanes, marked crossings enhance pedestrian safety, particularly for people using wheelchairs and other mobility...
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
§1193.51(e) TTY signal compatibility
Products, including those providing voice communication functionality, shall support use of all cross-manufacturer non-proprietary standard signals used by TTYs....
-
Attachment I: Program Access in Existing Facilities
Attachment I: Program Access in Existing Facilities
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
704.11.1 Parapet construction
Where the roof slopes toward a parapet at a slope greater than two units vertical in 12 units horizontal (16.7-percent slope), the parapet shall extend to the same height as any portion...
-
11B-505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
American Standard Home Cadet Bidet 5023.100
deck-mounted fitting • Vitreous china • Flushing rim and vertical cleansing spray • Integral overflow • Two bolt caps included Shown with 7391.733 Hampton Bidet Fitting with metal cross...
-
Sides of Curb Ramps [4.7.5]
Where pedestrians cross the ramp, curb ramps are required to have side flares; sharp returns present tripping hazards....
-
Openings [§302.3]
Surface Opening (Cross Section)...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
General (R304.1) (Section-by-Section Analysis)
Blended transitions are raised pedestrian street crossings, depressed corners, or similar connections between the pedestrian access route at the level of the sidewalk and the level of the...
-
R208 Detectable Warning Surfaces (Section-by-Section Analysis)
; Pedestrian refuge islands; Pedestrian at-grade rail crossings not located within a street or highway; Boarding platforms at transit stops for buses and rail vehicles...
-
Roundabouts (Section-by-Section Analysis)
Pedestrian street crossings at roundabouts can be difficult for pedestrians who are blind or have low vision to identify because the crossings are located off to the side of the pedestrian...
-
Beveled: ADA Standard Section 303.3
Section 303.3 covers the current ADA Standards for beveled level changes.
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
Rise
The maximum length of a run is determined by the rise (30 inches maximum) and the slope: Max. Rise Slope Max. Length Max. Rise Slope Max....
-
Elongated surface openings must be perpendicular to the dominant direction of travel, but what if there is no dominant direction of travel?
When there is no dominant direction of cross traffic, openings must be limited to ½” in both dimensions. ...
