Knee Clearance Height (KCH) 685...
Search Results "Vertical Clearance"
Filters
Commonly Searched Documents
-
Appendix 3 - Comparison of US Standards to IDEA Center Research
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
Vertices shall be radiused between 1/8 inch (3.2 mm) minimum and ¼ inch (6.4 mm) maximum....
-
11B.707.7.1.1 Vertically mounted display screen
Where display screens are mounted vertically or tipped away from the viewer less than 30 degrees, the center line of the display screen and other display devices shall be no more than 52...
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADAS] 303.2 Vertical. ...
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADA Standards] 303.2 Vertical....
-
Door stop
[See subsections ...]
-
Section 35.151(e) Social service center establishments
Section 35.151(e) Social service center establishments In the NPRM, the Department proposed a new Sec. 35.151(e) requiring group homes, halfway houses, shelters, or similar social...
-
A4.17.5 Doors
To make it easier for wheelchair users to close toilet stall doors, doors can be provided with closers, spring hinges, or a pull bar mounted on the inside surface of the door near...
-
4.9.4 HANDRAILS
Stairways shall have handrails at both sides of all stairs. Handrails shall comply with 4.26 and shall have the following features: (1) Handrails shall be continuous along both...
-
A4.17.5 DOORS
To make it easier for wheelchair users to close toilet stall doors, doors can be provided with closers, spring hinges, or a pull bar mounted on the inside surface of the door near...
-
4.8.5* HANDRAILS
If a ramp run has a rise greater than 6 in (250 mm) or a horizontal projection greater than 72 in (1830 mm), then it shall have handrails on both sides. Handrails are not required on...
-
Vertical Surface Discontinuities
Vertical Surface Discontinuities. Vertical differences in level between two adjacent surfaces....
-
§ 35.151(g) Assembly areas
(g) Assembly areas. Assembly areas subject to the proposed standards shall comply with the provisions applicable to assembly areas, including, but not limited to, sections 221 and...
-
§ 35.151(g) Assembly areas.
(g) Assembly areas. Assembly areas subject to this section shall comply with the provisions of the 2010 Standards applicable to assembly areas, including, but not limited to,...
-
7(2)(b)
(b) Bathrooms that have reinforced walls for grab bars (see Requirement 6) would meet section 100.205(c)(3)(iv) if: Note: Clear floor space beside tub may overlap with clear floor...
-
28.1 Q. If an architect or builder chooses to follow the bathroom specifications in Requirement 7...are the other bathrooms in the dwelling unit required to have reinforced walls for grab bars?
A. Yes. Requirement 6 of the Guidelines requires reinforced walls in bathrooms for later installation of grab bars. Even though Requirement 6 was not repeated under Requirement...
-
A. Arena Assembly Seating:
PSE shall provide at least 99 wheelchair accessible seats in The Palace in compliance with the wheelchair space requirements set forth in §802.1 of the 2010 Standards, in...
-
Comfort Designs Comfort Care™ Grab Bars
Now you don’t have to compromise strength for warmth or softness for durability. With ComfortCare™ you can get it all with a lifetime warranty. Properly installed as original...
-
Standards Specific to Assembly Areas
Dispersion of Wheelchair Spaces: Box Seats: Wheelchair spaces must be provided and located in not fewer than 20% of all boxes.Wheelchair spaces must be dispersed vertically, horizontally...
-
Clearance
Section 403.5 specifies a continuous clearance of 36 inches minimum for walking surfaces....
-
Priority 2: Access to Goods & Services
Word Fillable Form (2.5MB) Word Non-Fillable Form (2.4MB) PDF Non-Fillable Form (1.4MB)
-
Rough Form and Foundation Inspection
11B-403 Verify forms for sidewalks, ramps, landings, curb ramps and clear floor spaces are correctly installed so proper slopes, cross slopes, widths and clearances...
