A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum shall be provided. Knee and toe space complying with Section 11B-306...
Search Results "Grab Bar Clearance"
Filters
Commonly Searched Documents
-
11B-904.4.2 Forward approach
-
11B-904.4.2 Forward approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum shall be provided. Knee and toe space complying with Section 11B-306...
-
1133A.7.1 Plumbing protection
Water supply and drain pipes under kitchen sinks shall be insulated or otherwise covered to protect against contact. There shall be no sharp or abrasive surfaces under kitchen sinks.
-
Handrails [4.8.5]
Since 1½ inch pipe has an outside diameter close to 2 inches, it is important that handrails mounted to walls still provide the 1½ inch (absolute) knuckle clearance....
-
Can clear floor/ground space or turning space overlap other space requirements?
Yes, clear floor or ground spaces and turning space can overlap other required clearances, including other clear floor spaces, door maneuvering clearances, and fixture clearances....
-
Lateral grab bar use
The lateral grab bar was used least by subjects for the Adjustable gap protocol and most for the Side guard protocol....
-
609 Grab Bars
Section 609 covers grab bars at water closets, bathtubs, and showers. Specifications address size, spacing, position, surfaces, fittings, and structural strength....
-
Figure 307.4 Vertical Clearance – Drawing from the U.S. Access Board
-
307.4 Door Opening Vertical Clearance
-
Attachment E
The rear grab bar is too short. ...
-
Beds: ADA Standard Section 807.2.3
Where beds are provided, clear floor space complying with 305 shall be provided on at least one side of the bed. The clear floor space shall be positioned for parallel approach to...
-
11B-807.2.3 Beds
Where beds are provided, clear floor space complying with Section 11B-305 shall be provided on at least one side of the bed. The clear floor space shall be positioned for parallel...
-
11B-405.7.5 Doorways
Where doorways are located adjacent to a ramp landing, maneuvering clearances required by Sections 11B-404.2.4 and 11B-404.3.2 shall be permitted to overlap the required landing area....
-
§100.205(c)(3)
(3) All premises within covered multifamily dwelling units contain the following features of adaptable design:
-
5.8.2.1 Height of Breast Platform at Time of Measurement
The NPRM proposed measuring the knee clearance under the breast platform at 27 inches above the ground....
-
Just Manufacturing Stainless Steel Cup Strainer ADA Compliant Drain System
Body of stainless steel. Strainer of stainless steel. Stopper of rubber. 17 gauge chrome plated brass tailpiece. Die-cast zinc lock...
-
McGuire Manufacturing Co., Inc. 1151AWC: Offset with 151 Stainless Steel Basket Strainer
Offset sink strainer with stainless steel basket strainer with stainless steel basket. 2 3/4" x 4 3/8" OD.
-
McGuire Manufacturing Co., Inc. 155LATWC: Offset Lift and Turn PO Plug
Wheelchair lavatory strainer. Furnished with heavy brass elbow and 17GA seamless brass offset tailpiece. 8 3/4" x 5 1/8" OD.
-
4. Bed transfer space
4. Bed transfer space: A 30-inch by 48-inch clear floor space facilitates transfer from a wheelchair to the bed.
-
5. Bed with clear floor space
5. Bed with clear floor space for a side approach next to bed.
-
R402 Protruding Objects
R402 Protruding Objects
-
4.8.5(3)
(3) The clear space between the handrail and the wall shall be 1 - 1/2 in (38 mm).
-
1010.1.5 Floor elevation
There shall be a floor or landing on each side of a door. Such floor or landing shall be at the same elevation on each side of the door. Landings shall be level except for exterior...
-
Forward Approach
Forward Approach Knee and toe clearances specified for lavatories in 4.19, which recognize space for plumbing (see page 75), can be applied to sinks....
