Level changes greater than ½ inch high would be required to be ramped....
Search Results "Curb Ramp Top Landing"
Commonly Searched Documents
- 
    
  
  Changes in Level at Entry to Wheelchair Spaces (M303.3)
  
 - 
    
  
  5.8.1.2.3 Double Ramped Entry - Edge Protection on the Platform sides Recommendations
  
5.8.1.2.3 Double Ramped Entry - Edge Protection on the Platform sides Recommendations The Committee recommends a minimum two-inch high edge protection on both sides of the platform for...
 - 
    
  
  406.3 Sides of Curb Ramps
  
Where provided, curb ramp flares shall not be steeper than 1:10....
 - 
    
  
  5.8.1.2.2 Single Ramped Entry – Edge Protection on the Platform and Platform Sides
  
5.8.1.2.2 Single Ramped Entry – Edge Protection on the Platform and Platform Sides....
 - EZ Dock EZ TRAIL® Modular Walkway
 - 
    
  
  4.1.2(5)
  
EXCEPTION: Accessible ramps complying with 4.8 or, if no other alternative is feasible, accessible platform lifts complying with 4.11 may be used in lieu of an elevator....
 - Simplified Building Concepts: ADA - Building an Upright
 - Simplified Building Concepts: Assembling the ADA Railing
 - Simplified Building Concepts: ADA - Message to Contractors
 - Simplified Building Kee Access ADA Railings
 - 
    
  
  1131A.2 Changes greater than ½ inch
  
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
 - 
    
  
  1131A.2 Changes greater than ½ inch
  
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
 - 
    
  
  1131A.2 Changes greater than ½ inch
  
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
 - 
    
  
  Cross Slope and Surfaces [4.8.6]
  
Ramp surfaces must comply with requirements for ground and floor surfaces and be "stable, firm, and slip-resistant." A specific level of slip-resistance is not mandated....
 - 
    
  
  5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces
  
5.9.2 Standing Supports on Ramped Entry Raised Platforms with Wheelchair Spaces....
 - seca 676 r Digital Wheelchair Scale with Handrail and Integrated RS232 Interface
 - 
    
  
  11B-406.2.2 Sides of curb ramps
  
Where provided, curb ramp flares shall not be steeper than 1:10. FIGURE 11B-406.2.2 ‡‡ SIDES OF CURB RAMPS...
 - 
    
  
  5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations
  
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations The Committee recommends a two-inch high edge protection on the back of the platform...
 - 
    
  
  Problem Three (Accessible Route)
  
Solution: Install a portable ramp....
 - seca 684 r Digital Multifunctional Scale with Integrated RS232 Interface
 - 
    
  
  11B-505.9 Fittings
  
Handrails shall not rotate within their fittings.
 - 
    
  
  505.9 Fittings
  
Handrails shall not rotate within their fittings.
 - 
    
  
  505.9 Fittings
  
Handrails shall not rotate within their fittings.