(3) Specify the schedule for taking the steps necessary to achieve full accessibility in order to comply with paagraph [sic] (a) of this section and, if the time period of the transition...
Search Results "Zero Curb Transition"
-
§104.22(e)(3)
-
4.7.11 Islands
Any raised islands in crossings shall be cut through level with the street or have curb ramps at both sides and a level area at least 48 in (1220 mm) long between the curb ramps in the part...
-
11B-206.2.1 Site arrival points
.) ◼ [ADA Title II] §35.151(i) New Construction and Alterations; Curb Ramps....
-
Problem Two (Accessible Route)
Problem Two: The accessible route crosses a curb and no curb ramp is provided. Solution: Install a portable ramp....
-
NPRM and Comments
In a few cities, there are systems that use vintage inaccessible vehicles to provide regular public transit service....
-
Equivalent Facilitation [2.2]
The Access Board can provide further guidance on what may be considered equivalent but there is no process for certifying alternative methods except in transit facilities covered by DOT...
-
Detectable Warning Surfaces on Boarding Platforms Used by Buses and Rail Vehicles, and Boarding and Alighting Areas Used by Rail Vehicles (Section-by-Section Analysis)
The 1991 ADAAG and 2004 ADA and ABA Accessibility Guidelines contain a requirement for detectable warning surfaces on rail platforms.32 The proposed guidelines adapt this requirement to transit...
- Intelligent Assistive Technology and Systems Lab
-
Allowances for Typical Roadway Geometry
The draft guidelines also permitted the cross slope of pedestrian access routes within midblock pedestrian street crossings and of curb ramps at midblock pedestrian street crossings to equal...
-
11B-411.1.1 Floor designations
Floor designations shall be "one" (1) or "zero" (0) at the main entry level and shall increase by one for each successive higher story or level....
-
Kitchen Counters, Walls, and Floors
Staggered stud construction to prevent noise transmission to other rooms Zero clearance kitchen entries with less than 1/4” change of elevation throughout the accessible route. ...
-
11B-411.1.1 Floor designations
Floor designations shall be "one" (1) or "zero" (0) at the main entry level and shall increase by one for each successive higher story or level....
-
11B-411.1.1 Floor designations
Floor designations shall be "one" (1) or "zero" (0) at the main entry level and shall increase by one for each successive higher story or level....
-
Minimum Required Attributes
Minimum Required Attributes: The Review Team has identified a list of minimum required attributes that need to be included within a State’s ADA transition plan....
-
Baseline
ramps and blended transitions at pedestrian street crossings (R208.1 and R305) Will affect state and local transportation departments that do not currently provide detectable warning...
-
4.7.7 Detectable Warnings
A curb ramp shall have a detectable warning complying with 4.29.2. The detectable warning shall extend the full width and depth of the curb ramp....
-
11B-405.8 Handrails
Curb ramps do not require handrails. At door landings, handrails are not required on ramp runs less than 6 inches (152 mm) in rise or 72 inches (1829 mm) in length....
-
11B-405.8 Handrails
Curb ramps do not require handrails. At door landings, handrails are not required on ramp runs less than 6 inches (152 mm) in rise or 72 inches (1829 mm) in length....
- GameTime ADA Wide Ramp Attachment 3D
- Inpro Corporation JointMaster® 103 Series-VCT Expansion Joint Systems
- Detectable Warning Systems, Inc. AlertTile® Detectable Warning
-
11B-406.6 Islands
Raised islands in crossings shall be cut through level with the street or have curb ramps at both sides....
-
§ 38.83(c)(3) Ramp threshold
The transition from roadway or station platform and the transition from vehicle floor to the ramp or bridge plate may be vertical without edge treatment up to 1/4 inch....
-
§ 38.125(c)(3) Ramp threshold
The transition from station platform to the ramp or bridge plate and the transition from car floor to the ramp or bridge plate may be vertical without edge treatment up to 1⁄4 inch....