OPTIONAL: To anchor table to a concrete surface, use Model ANC6-4 Anchor Kit (Concrete Screws) and Model ANG-3 Anchor Kit (Anchor Straps)....
Search Results "Surface Smoothness"
-
Pilot Rock WXT and WXTH Picnic Table Using Aluminum
-
Pilot Rock WUT and WUTH Picnic Table - Using Aluminum
OPTIONAL: To anchor table to a concrete surface, use Model ANC6-4 Anchor Kit (Concrete Screws) and Model ANG-5 Anchor Kit (Anchor Straps)....
-
Pilot Rock XT Series Side Accessible Picnic Table Using Recycled Plastic
OPTIONAL: To anchor table to a concrete surface, use Model ANC6-4 Anchor Kit (Concrete Screws) and Model ANG-3 Anchor Kit (Anchor Straps)....
-
609.7 Installation
Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space....
-
UltraPlay Getting Started Installation Video
Learn how to get started and prepare for the installation of your UltraPlay playground structure with this first of several installation videos.
-
AccessRec AccessMat Beach Access Mat System
Comfortable and Safe Developed specifically for pedestrian traffic, AccessMat™ provides a barefoot friendly surface for beach goers....
-
11B-609.7 Installation
Grab bars shall be installed in any manner that provides a gripping surface at the specified locations and that does not obstruct the required clear floor space....
-
2. Standing Supports
For horizontal standing supports, the Access Board proposed a gripping surface of 4 inches long minimum, the top of which would be required to be located 34 inches minimum and 38 inches...
-
Check-Out Aisles [7.3]
Writing surfaces must be 36 inches maximum from the floor....
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
Poured in Place Rubber
The surface cost for PIP ranged from $6.59/sq. ft. to $19.80/sq. ft. ...
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
The Brewer Company, LLC
Company, LLC Minority Report The Brewer Company, LLC 01-Oct-2013 Final Report Medical Diagnostic Equipment Accessibility Standards Advisory Committee Section 5.1.3 Transfer Surface...
-
How to Measure Transfer Surface Height
How to Measure Transfer Surface Height Regardless of the final decision on the low height measurement, the Subcommittee agreed that the height of the transfer surface would be measured...
-
4.3.3 Slope
When the surface is not paved or is not elevated above the natural ground, slopes not steeper than 1:33 (3 percent) shall be permitted where necessary for drainage. ...
-
Clearances Around Gripping Surfaces
Guidelines specify the following clearances around grab bars to ensure sufficient space for a person to grasp the grab bar: 1½ inches absolute clearance between grab bars and the adjacent wall surfaces...
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
(2) Transfer Surface Location for Diagnostic Equipment Used in the Seated Position
Transfer onto these types of diagnostic equipment must be made from either long side, similar to the side transfer surface described above....
-
§ 38.125(b)(6) Platform surface
(6) Platform surface. The lift platform surface shall be free of any protrusions over 1/4 inch high and shall be slip resistant....
-
2010 ADA Standards - Plan Review Tool - Slopes
2010 ADA Standards - Plan Review Tool - Slopes Click here to view/download the pdf "2010 ADA Standards - Plan Review Tool - Slopes" (774 KB) * * * * * * *
-
1017.6 Openings
Openings in the surface of trails, passing spaces, and resting intervals shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1017.6 Openings. ...
-
1133A.4.1 Exceptions
Two 15-inch (381 mm) wide minimum breadboards may be provided in lieu of the required 30 inches (762 mm) of countertop work surface, and used without meeting the repositioning requirements...
