Conditions for an exception from a technical requirement are circumstances found in natural environments, construction practices, or certain laws that may make compliance with the requirements...
Search Results "Compliance Coordinator"
Filters
Commonly Searched Documents
-
Conditions for an exception
-
Employers' Guide to Including Employees with Disabilities in Emergency Evacuation Plans
Accommodation and Compliance Series: Employers' Guide to Including Employees with Disabilities in Emergency Evacuation Plans By Beth Loy, Ph.D and Linda Carter Batiste, J.D....
-
AISLE
., that provides clearances in in compliance with this code....
-
11B-606.7 Sink depth
Where a forward approach is required at a sink, knee and toe clearance shall be provided in compliance with Section 11B-306....
-
AISLE
., that provides clearances in compliance with this code....
-
Education's Intent To Revise its Section 504 Regulations To Adopt the 2010 Title II ADA Standards
For these reasons, in coordination with DOJ, we are planning to initiate rulemaking to address the relevant standards of Education's Section 504 regulations for new construction and alterations...
-
Technical Memorandum TM 2013-18 Sinks
TM 2013-18 Sinks Effective Date: June 1, 2013 2012 TAS Reference: 212.3 and 804.4 Kitchens / Kitchenettes with Sinks If a sink is provided in a space that is subject to compliance...
-
Steps to Minimize Significant Economic Impacts on Small Entities
When an entity determines that a condition does not permit full compliance with a provision, compliance is required to the extent practicable....
-
Prioritization
Compliance is required up to the point the 20% cost cap is reached, even where it does not result in a fully accessible path of travel....
-
How the ADA Standards are Enforced
Nor are building departments required or authorized by the ADA to enforce the ADA Standards (some building departments even include a disclaimer on their plan checks indicating that ADA compliance...
-
American Standard Cadet Bidet 5023.111
Integral overflow • Two bolt caps included Shown with 2000.011 Ceramix Bidet Fitting (not included) Nominal Dimensions: 654 x 391 x 378mm (25-3/4" x 15-3/8" x 14-7/8") Compliance...
-
Sec. 469.151(a)(2)
(2) the owner of the building or facility for which a request for a waiver or modification is made, or the owner's designated agent, presents proof to the commission that compliance with...
-
§8.57(c)(1)
(1) The responsible civil rights official has advised the applicant or recipient of its failure to comply and has determined that compliance cannot be secured by voluntary means;...
-
AISLE
., that provides clearances in in compliance with this code....
-
§ 35.172(b)
(b) The designated agency may conduct compliance reviews of public entities in order to ascertain whether there has been a failure to comply with the nondiscrimination requirements of this...
-
§ 38.153(c)(2) Exception
Where compliance with the door width requirement of paragraph (c)(1) of this section is not feasible, the minimum door width shall be 27 in (685 mm)....
-
II-6.5000 Alterations to historic properties
Under those provisions, alterations should be done in full compliance with the alterations standards for other types of buildings....
-
11B-233.1 General
Is compliance with Chapter 11B required?...
-
Besam SW200i Overhead Concealed Swing Door Operator
Safety compliance The Besam SW200i-OHC overhead concealed swing door operator complies with ANSI A156.10 and ANSI A156.19 Technical Description: ANSI compliance: field selectable...
-
1019.1 General
Compliance is not practicable due to terrain. 2. Compliance cannot be accomplished with the prevailing construction practices. 3....
-
1019.1 General
Compliance is not practicable due to terrain. 2. Compliance cannot be accomplished with the prevailing construction practices. 3....
-
III-7.1000 General
Can local building inspectors certify compliance with the ADA? No. The ADA is not enforced by State or local building inspectors....
-
11B-1008.2.6.1 Accessibility
Ground surfaces shall be inspected and maintained regularly and frequently to ensure continued compliance with ASTM F 1951....
-
§382.151(d)
The CRO is intended to be the carrier's “expert” in compliance with the requirements of this part....
