Transfer supports shall comply with M305.2.
Search Results "Adjusted Construction Cost"
Commonly Searched Documents
-
M305.2 Transfer Supports
- California Division of the State Architect (DSA)
-
1. Costs: Summary of Methodology and Results
For purposes of assessing the likely cost impact of these five requirements over the 12-year regulatory time horizon, the Final RA uses a unit cost approach that reflects both initial costs...
- How to: adjust your parking brakes
-
§ 36.308 Seating in assembly areas.
such specialty seating area, it shall provide those services or amenities to individuals with disabilities and their companions at other designated accessible locations at no additional cost...
-
11B-104.1.1 Construction and manufacturing tolerances
Advisory 11B-104.1.1 Construction and manufacturing tolerances. ...
-
§ 36.401(d) Elevator exemption.
(d) Elevator exemption.
-
§ 36.401(d)(2)
(2) This section does not require the installation of an elevator in a facility that is less than three stories or has less than 3000 square feet per story, except with respect to...
-
§ 36.401(d)(3)
(3) The elevator exemption set forth in this paragraph (d) does not obviate or limit, in any way the obligation to comply with the other accessibility requirements established in...
-
Sec.36.401(d) Elevator exemption
(d) Elevator exemption.
-
Sec.36.401(d)(2)
(2) This section does not require the installation of an elevator in a facility that is less than three stories or has less than 3000 square feet per story, except with respect to...
-
Sec.36.401(d)(3)
(3) The elevator exemption set forth in this paragraph (d) does not obviate or limit, in any way the obligation to comply with the other accessibility requirements established in...
- Benefits of Adjustable Sound and Speed Technology
-
M305.2.2.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M305.2.2.1 shall be 15 inches (380 mm) long minimum. Transfer supports shall be positioned along 13 ½ inches...
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
M305.2.1.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be capable of supporting transfer on each side of the transfer surface.
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side.
-
M305.2.2.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be 28 inches (710 mm) long minimum and shall be positioned along the width of transfer...
-
Typical Transfer Techniques: Staff Assistance and Patient Lifts
Typical Transfer Techniques: Staff Assistance and Patient Lifts Some individuals will need additional assistance to get on and off an exam table, even if it lowers to 17‒19 inches...
-
5.3.1 Permitted Obstructions to Transfer Sides for Equipment Used by Patients in a Supine, Prone, Side-Lying or Seated Position
5.3.1 Permitted Obstructions to Transfer Sides for Equipment Used by Patients in a Supine, Prone, Side-Lying or Seated Position. A 3-inch maximum obstruction is permitted at transfer...
-
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position. Transfer supports should be positioned 6 inches minimum and 19 inches maximum...
-
III. Costs and Benefits
The Department estimates that the costs associated with this final rule will be minimal for two reasons....
-
Water Hydrants
Locate water spouts 11 inches (280 Applying the Forest Service Outdoor Recreation Accessibility Guidelines 68 Constructed Features in Recreation Sites millimeters) [sic] minimum and 12 inches...
- Allegion Von Duprin 98/99 Series Von Duprin CVC Traditional and Quick Adjust Bottom Latch Adjustment