The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
Search Results "Head End Wall"
Filters
Commonly Searched Documents
-
11B-610.3.1 Rectangular seats
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
608.5.1 Transfer Type Shower Compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1220 mm...
-
Controls [4.21.5]
Controls [4.21.5] Controls and shower units can be located on any wall but where a folding seat is provided they must be located to be within reach of a person on the seat....
-
11B-604.7.2 Disposal units
Sanitary napkin disposal units, if provided, shall comply with Section 11B-309.4 and shall be wall mounted and located on the sidewall between the rear wall of the toilet and the toilet...
-
11B-608.5.1 Transfer type shower compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1219 mm...
-
Taking Measurements
Rest one end of the level at the highest point of the sloped surface and lift the other end (as shown in the illustration) until the bubble is in the middle of the tube....
-
Salsbury Industries See Through Metal Locker Triple Tier 1 Wide
height (add 6" for legs) Units have compartment sizes that are 12" wide, 24" high and 12", 15" or 18" deep Available as 1 wide or 3 wide units Each locker compartment includes 3 wall...
-
Salsbury Industries See Through Metal Locker Double Tier 1 Wide
height (add 6" for legs) Units have compartment sizes that are 12" wide, 36" high and 12", 15" or 18" deep Available as 1 wide or 3 wide units Each locker compartment includes 3 wall...
-
Salsbury Industries See Through Metal Locker Double Tier 3 Wide
height (add 6" for legs) Units have compartment sizes that are 12" wide, 36" high and 12", 15" or 18" deep Available as 1 wide or 3 wide units Each locker compartment includes 3 wall...
-
Salsbury Industries See Through Metal Locker Triple Tier 3 Wide
height (add 6" for legs) Units have compartment sizes that are 12" wide, 24" high and 12", 15" or 18" deep Available as 1 wide or 3 wide units Each locker compartment includes 3 wall...
-
Accessible Routes
The accessible route must comply with ADAAG provisions for location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level,...
-
§40.3(a)
If the design of a structure commenced prior to that date, the standards shall be made applicable to the maximum extent practicable, as determined by the head of the department, agency,...
-
604.2 Location
The water closet shall be positioned with a wall or partition to the rear and to one side....
-
704.11.1 Parapet construction
Parapets shall have the same fire-resistance rating as that required for the supporting wall, and on any side adjacent to a roof surface, shall have noncombustible faces for the uppermost...
-
M305.3.2 Vertical Position
Where the support is vertical, it shall be 18 inches (455 mm) minimum in length and the bottom end of the support shall be 34 inches (865 mm) high minimum and 37 inches (940 mm) high maximum...
-
F103 Modifications and Waivers
Postal Service to modify or waive the accessibility standards for buildings and facilities covered by the Architectural Barriers Act on a case-by-case basis, upon application made by the head...
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
804.2.1 Pass Through Kitchen
In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing...
-
11B-804.2.1 Pass through kitchen
In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing...
-
11B-604.7.2 Disposal units
Sanitary napkin disposal units, if provided, shall comply with Section 11B-309.4 and shall be wall mounted and located on the sidewall between the rear wall of the toilet and the toilet...
-
11B-804.2.1 Pass through kitchen
In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing...
-
Living Room
Arms well forward on chairs Biodegradable grass cloth Wall texture offers traction when leaning on the wall to prevent slip and fall....
-
Communication During Leave and Prior to Return to Work
Near the end of the three month leave, the employee requests an additional 30 days of leave....
