Minimum character height shall comply with Table 11B-703.5.5....
Search Results "Uppercase Character (Visual)"
Filters
Commonly Searched Documents
-
11B-703.5.5 Character height
-
T702 Signs
[See subsections ...]
-
11B-703.5.10 Format
Text shall be in a horizontal format.
-
11B-703.5.10 Format
11B-703.5.10 Format. Text shall be in a horizontal format.
-
11B-703.5.10 Format
Text shall be in a horizontal format.
-
703.1 General
Where both visual and tactile characters are required, either one sign with both visual and tactile characters, or two separate signs, one with visual, and one with tactile characters, shall...
-
Figure 703.2.5 Height of Raised Characters – Drawing from the U.S. Access Board
-
11B-216.4.4 Delayed egress locks
Signs required by Chapter 10, Section 1008.1.9.7, item 5.1 at doors with delayed egress locks shall comply with Sections 11B-703.1 _|Signs; General|_ 11B-703.2 _|Signs; Raised Characters...
-
11B-216.4.4 Delayed egress locks
Signs required by Chapter 10, Section 1010.1.9.7, Item 6.4 at doors with delayed egress locks shall comply with Sections 11B-703.1 _|Signs; General|_ 11B-703.2 _|Signs; Raised Characters...
-
Characters
Letters, numbers, punctuation marks and typographic symbols.
-
CHARACTERS
[DSA-AC] Letters, numbers, punctuation marks and typographic symbols.
-
11B-703.5.8 Character spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
Routes and Destinations: ADA Standard Section 810.6.2
EXCEPTION: Where sign space is limited, characters shall not be required to exceed 3 inches (75 mm). Advisory 810.6.2 Routes and Destinations....
-
11B-810.6.2 Routes and destinations
Exception: Where sign space is limited, characters shall not be required to exceed 3 inches (76 mm). Advisory 11B-810.6.2 Routes and destinations....
-
Size: ADA Standard Section 407.4.8.1.1
Section 407.4.8.1.1 covers the current ADA Standards for size of visible elevator car position indicators.
-
11B-407.4.8.1.1 Size
Characters shall be ½ inch (12.7 mm) high minimum....
-
11B-411.4.11.1 Height
Floor destination characters shall be 1 inch (25 mm) high minimum complying with Section 11B-703.5.3....
-
11B-411.4.11.1 Height
Floor destination characters shall be 1 inch (25 mm) high minimum complying with Section 11B-703.5.3....
-
11B-411.4.11.1 Height
Floor destination characters shall be 1 inch (25 mm) high minimum complying with Section 11B-703.5.3....
-
IV.B.2.
Characters on signs required by paragraph IV.B.1 of this appendix shall have a width-to-height ratio between 3:5 and 1:1 and a stroke width-to-height ratio between 1:5 and 1:10, with a minimum...
-
Figure 407.2.3.1 Floor Designations on Jambs of Elevator Hoistway Entrances – Drawing from the U.S. Access Board
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
Character Proportion [4.30.2]
Character Proportion [4.30.2] Very thick or thin characters and character strokes can be difficult to read....
-
11B-703.8.4 Character height
11B-703.8.4 Character height. The uppercase letter “I” shall be used to determine the allowable height of all low resolution VMS characters of a font....
