406.3 Sides of Curb Ramps. Where provided, curb ramp flares shall not be steeper than 1:10. Figure 406.3 Sides of Curb Ramps...
Search Results "Hinge Side Clearance"
Filters
Commonly Searched Documents
-
406.3 Sides of Curb Ramps
-
406.3 Sides of Curb Ramps
Figure 406.3 Sides of Curb Ramps...
-
11B-305.4 Knee and toe clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with Section 11B-306....
-
11B-306.3 Knee clearance
[See subsections ...]
-
11B-306.2 Toe clearance
[See subsections ...]
-
11B-406.2.2 Sides of curb ramps
FIGURE 11B-406.2.2 ‡‡ SIDES OF CURB RAMPS...
-
TownSteel THSP179 Standard Duty Spring Hinge
Hinges to be provided in the type and size as recommended by the Manufacturer....
-
11B-604.8.1.1.2 Maneuvering space with side-opening door
In a wheelchair accessible compartment with a door located in the side wall or partition, either in-swinging or out-swinging, a minimum 60 inches (1524 mm) wide and 60 inches (1524 mm) deep...
-
11B-604.8.1.4 Toe clearance
At least one side partition shall provide a toe clearance of 9 inches (229 mm) minimum above the finish floor and 6 inches (152 mm) deep minimum beyond the compartment-side face of the partition...
-
4.3.4 Knee and Toe Clearances
Hence, to accommodate a particular percentage of users, the side profile of a design element (shown by dotted line) should not extend outside the corresponding shaded area....
-
11B-411.4.3 Platform to hoistway clearance
Platform to hoistway clearance shall comply with Section 11B-407.4.3....
-
§ 36.304(b)(9)
(9) Installing offset hinges to widen doorways;...
-
Sec.36.304(b)(9)
(9) Installing offset hinges to widen doorways;...
-
406.3 Sides of Curb Ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
-
11B-306.3.4 Clearance reduction
Between 9 inches (229 mm) and 27 inches (686 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches...
-
Doorways without Doors or Gates, Sliding Doors, and Folding Doors: ADA Standard Section 404.2.4.2
Section 404.2.4.2 covers the current ADA Standards for maneuvering clearances at doorways without doors or gates, sliding doors, and folding doors.
-
11B-404.2.4.2 Doorways without doors or gates, sliding doors, and folding doors
TABLE 11B-404.2.4.2 MANEUVERING CLEARANCES AT DOORWAYS WITHOUT DOORS OR GATES, MANUAL SLIDING DOORS, AND MANUAL FOLDING DOORS MINIMUM MANEUVERING CLEARANCE...
-
Side Transfer Surface
A transfer surface located within the length of the examination surface that allows patient transfer on two opposing sides of the examination surface....
-
Re: 404.2.4.3 Recessed Doors and Gates
A barrier within 18" of the latch side of a push approach door will trigger the extra requirements....
-
306.2.4 Additional Clearance
Space extending greater than 6 inches (150 mm) beyond the available knee clearance at 9 inches (230 mm) above the finish floor or ground shall not be considered toe clearance....
-
11B-809.10.8.4 Knee and toe clearance
Knee and toe clearance shall be provided and comply with Section 11B-306....
-
Door Maneuvering Clearance
, latch side, hinge side)....
-
R406.3 Unobstructed Side Reach
R406.3 Unobstructed Side Reach....
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
