Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
Search Results "Side Grab Bar"
Filters
Commonly Searched Documents
-
11B-406.5.10 Diagonal curb ramps
-
5.7.1 Lift Compatibility Clearance in Base for Equipment Used by Patient in Supine, Prone, or Side-Lying Position
5.7.1 Lift Compatibility Clearance in Base for Equipment Used by Patient in Supine, Prone, or Side-Lying Position....
-
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Built-Up Curb Ramps
Built-Up Curb Ramp with Side Flares Recommendations: Provide edge protection along the sides of built-up curb ramps to prevent tipping hazards....
-
11B-606.2 Clear floor space
A parallel approach complying with Section 11B-305 shall be permitted to a kitchen sink in a space where a cook top or conventional range is not provided and to wet bars. 2. Reserved...
-
1607A.8 Loads on handrails, guards, grab bars, seats and vehicle barriers
1607A.8 Loads on handrails, guards, grab bars, seats and vehicle barriers....
-
Wikk Industries Inc. Bollard With Push Plate PART#BPRT126SMFT32D (630)
12”x6”x42” Tall, 7ga. Formed 304 Satin Stainless Steel US32D (630), Surface mount with concealed mounting base, 1 prep for INGRESS’R ® ADA switch (630), Welded Flat top. Shown on...
-
SDC Bollard Post with Push Plate or Touch Panel
Alternative to wall mounted access control or switches for entry doors. Bollard post provide visibility and meet accessibility guidelines. Practical solution for surface mount or...
-
Wikk Industries Inc. PART#BPS SM-INGR CLEAR (628) with I36-3 CLEAR (628)
6”X6”X42” Tall, Clear Anodized Aluminum (628), Surface mount with concealed mounting base, 1 prep for INGRESS’R® ADA switch, Removable Black ABS cap Shown on the bollard- I36-3...
-
Wikk Industries Ingress'r Automatic Door Control
FEATURES: Weather resistant design allows interior or exterior application without adaptation UL® 15 amp. micro switch Crafted in clear anodized aluminum - will quote...
-
Wikk Industries Inc. PART# BPS SM-ING48 DB (710) with I36-3 Clear (628)
6”X6”X48” Tall, Dark Bronze Anodized Aluminum (710), Surface mount with concealed mounting base, 2 Preps for INGRESS’R® and card reader, Removable Black ABS Cap. **Customer can...
-
BEA Inc. LPR36 Series 36" Low Profile Push Plate
The LPR36 maximizes accessibility and independence for people with disabilities. The entire surface is “all-active” with four redundant membrane switches for consistent coverage. The...
-
5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
F248.1.1 Facilities Serving Beaches
Beach access routes shall be provided in a number complying with F248.2 where the entity that administers or manages a beach constructs or alters any of the following facilities to...
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable.
-
Notification Forms
Documentation is required where a condition for exception prohibits full compliance with a specific technical requirement. The documentation must include the reason that full...
-
Notifying the Access Board When an Entire Trail or Beach Access Route is Exempted [F204.4.1]
In the rare cases where an entire trail or beach access route is exempted, Federal agencies must notify the Access Board about the exemption. Sample notification forms are in the...
-
6.14.2 Gate Hardware
Gate hardware shall comply with operable controls requirements in ABAAS section 309.4 and 404.2.7.
-
1018.4 Clear Width
This section requires the clear width of beach access routes to be 60 inches minimum to enable individuals who use wheeled mobility devices to pass beach visitors traveling in the...
-
1018.3 Surface
This section requires the surface of beach access routes and resting intervals to be firm and stable.
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable.
-
1. Transfer Surface
[See subsections ...]
-
4.34.3(2)(b) Reach Depth More Than 10 in
(b) Reach Depth More Than 10 in (255 mm). Where the reach depth to the operable parts of any control as measured from the vertical plane perpendicular to the edge of the unobstructed...
