The cross slope of ramp runs shall not be steeper than 1:48....
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
M303.3.3.2 Cross Slope
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48....
-
Appendix 2: Survey Forms: Curb Ramps
Describe each curb ramp’s location: Curb Ramp D: Curb Ramp A: Curb Ramp E: Curb Ramp B: Curb Ramp F: Curb Ramp C: Curb Ramp G:...
-
A4.8.2 SLOPE AND RISE
Many people who have difficulty negotiating very long ramps at relatively shallow slopes can manage very short ramps at steeper slopes....
-
E. What are the General Requirements for Curb Ramps in the ADA Standards for Accessible Design?
One way to make curb ramps compliant with Title II of the ADA is to build them in accordance with the ADA Standards. 7 Following are the key characteristics of an accessible curb ramp according...
-
Approach: ADA Standard Section 904.2
All portions of counters required to comply with 904 shall be located adjacent to a walking surface complying with 403. Advisory 904.2 Approach....
-
Chapter 6 Addendum: Title II Checklist (Curb Ramps and Pedestrian Crossings)
’s curb ramps....
-
4.8.5(2)
(2) If handrails are not continuous, they shall extend at least 12 in (305 mm) beyond the top and bottom of the ramp segment and shall be parallel with the floor or ground surface (see Fig...
-
Openings in Trail Surfaces
Openings are gaps in the surface of a trail. Gaps include slots in a drainage grate and spaces between the planks on a puncheon, bridge, or boardwalk....
-
M304.2 Standing Surface (Section-by-Section Analysis)
The MDE NPRM proposed to require that the standing surface on which patients stand be slip resistant....
-
4.7.6 Built-up Curb Ramps
Built-up curb ramps shall be located so that they do not project into vehicular traffic lanes (see Fig. 13)....
-
4.7.6 BUILT-UP CURB RAMPS
Built-up curb ramps shall be located so that they do not project into vehicular traffic lanes (see Fig. 13)....
-
Floor [1014.3]
The floor surface within a camp shelter must be firm and stable....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with Section 11B-303....
-
11B-904.2 Approach
All portions of counters required to comply with Section 11B-904 shall be located adjacent to a walking surface complying with Section 11B-403. Advisory 11B-904.2 Approach....
-
§ 38.59 Floor surfaces
Floor surfaces on aisles, places for standees, and areas where wheelchair and mobility aid users are to be accommodated shall be slip-resistant....
-
1.1.3
1.1.3 A maximum overall design running slope for exterior accessible surfaces (other than ramps), such as sidewalks, of 4% (approximately 1:25) is recommended....
-
Hybrid Surface Systems
Hybrid Surface Systems There were a total of four sites with three different hybrid (HYB) surface systems evaluated in the study. ...
-
1003.2.2 Boarding Piers at Boat Launch Ramps
1003.2.2 Boarding Piers at Boat Launch Ramps. Accessible routes serving boarding piers at boat launch ramps shall be permitted to use the exceptions in 1003.2.2. EXCEPTIONS: 1....
-
Governmental Units Affected (R208 Detectable Warning Surfaces) (Section-by-Section Analysis)
UFAS did not contain a requirement for detectable warning surfaces on curb ramps. The Access Board is not aware of any state or local transportation departments that use UFAS....
-
Ground Surfaces: ADA Standard Section 1008.2.6
Ground surfaces on accessible routes, clear floor or ground spaces, and turning spaces shall comply with 1008.2.6. Advisory 1008.2.6 Ground Surfaces....
-
4.2.4 Height of Fire-Building Surface
The fire-building surface within a fire ring shall be at least 9 inches (230 mm) above the floor or ground....