space beyond the latch side of the door....
Search Results "Power Operated Door"
-
Entrances
-
Are spring hinges and gravity hinges considered “closers” in determining the size of maneuvering clearances?
Some approaches require additional maneuvering clearances when a door or gate is equipped with a closer because of the additional force that must be counteracted in proceeding through doors...
-
Technical Memorandum TM 2017-25 Door and Gate Surfaces
TAS 404.2.10 also includes Exceptions for (1) sliding doors, (2) tempered glass doors (3) doors and gates which do not extend to within 10 inches of the finish floor, and (4) existing doors...
-
Reach Ranges and Operable Parts
REACH RANGES AND OPERABLE PARTS Forward and side reach 11B-308.2/3 Over projections 11B-308.2.2/3.2...
-
Reach Ranges and Operable Parts
REACH RANGES AND OPERABLE PARTS Forward and side reach 11B-308.2/3 Over projections 11B-308.2.2/3.2...
-
Wagner Instruments Mark-10 M3 Digital Force Gauge
Power Requirements Continuous operation with 110 or 220 Vac power adapter. Rechargeable NiMH battery for up to 30 hours continuous use....
-
H25
Is the clear width of the door at least 32 inches (measured between the face of the door and the edge of the opening) when the door is open 90 degrees?...
-
Floor or Ground Surface: ADA Standard Section 404.2.4.4
Section 404.2.4.4 covers the current ADA Standards for floor or ground surfaces at door maneuvering clearances.
-
Doors, Doorways, and Gates
Section 206.5 provides scoping requirements for doors, doorways, and gates....
-
1132A.3, Item 3
Swinging doors shall be capable of opening at least 90 degrees....
-
1132A.3, Item 3
Swinging doors shall be capable of opening at least 90 degrees....
-
Paragraph (f) Operable with limited reach and strength (Section-by-Section Analysis)
Paragraph (f) Operable with limited reach and strength (Section-by-Section Analysis) Comment....
-
7. Q: What procedures should law enforcement officers follow to arrest and transport a person who uses a wheelchair?
Safe transport of other individuals who use manual or power wheelchairs might require departments to make minor modifications to existing cars or vans, or to use lift-equipped vans or buses...
-
SECTION 1008 DOORS, GATES AND TURNSTILES
SECTION 1008 DOORS, GATES AND TURNSTILES [DSA-AC] In addition to the requirements of this section, means of egress, which provide access to, or egress from, buildings or facilities where...
-
Wagner Instruments Mark-10 M4 Digital Force Gauge
Power Requirements Continuous operation with 110 or 220 Vac power adapter. Rechargeable NiMH battery for up to 30 hours continuous use....
-
Pager Charger (BE1260)
The Pager charger charges the Visit Pager receiver and can additionally power up to two Visit Bed-shakers....
-
SECTION 1132A DOORS
[See subsections ...]
-
SECTION 1132A DOORS
[See subsections ...]
-
Standard Stall
The clearances required for stall doors are different than those specified for conventional passage doors and gates in 4.13.6 since partition doors are generally lighter and easier to open...
-
302.4 Without Hearing (Section-by-Section Analysis)
This provision would clarify the requirements in existing 508 Standards §1194.31(c) and existing 255 Guidelines §1193.41(d) by specifying that provision of a mode of operation without hearing...
-
PC Doors Pocket Door E-Z Closer
PC Doors Pocket Door E-Z Closer...
-
Wagner Instruments Chatillon® DFE Digital Force Gauge
Operation Controls TCM and TCD motorized test stands (E-DFE)....
-
EXHIBIT D QUIKTRIP POLICY ON ACCESS, SERVICE, AND ASSISTANCE FOR CUSTOMERS WITH DISABILITIES
Common types of assistance that QuikTrip provides to customers with disabilities include the following: providing fueling assistance; cleaning windshields; opening doors; locating or retrieving...
-
1132A.4.1 Thresholds
Thresholds at the primary entry and required exit doors shall be no higher than ½ inch (12.7 mm)....
