Diagnostic equipment shall be usable with a patient lift and shall comply with M301.4.1 or M301.4.2.
Search Results "Head Height"
Filters
Commonly Searched Documents
-
M301.4 Lift Compatibility
-
M301.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface. Each transfer side...
-
Adjustable height/gap protocol
Adjustable height/gap protocol: From the initial setup, a gap separating the device and platform was introduced with the plywood blocks of 3.5” (8.9cm) and then the height of platform was...
-
M305.2.2 Length (Section-by-Section Analysis)
Advisory Committee also recommended 15 inches in length stating that this would provide continuous support for patients and still accommodate the articulation that is necessary for the head...
-
Check Height and Location of the Pushbutton
Check Height and Location of the Pushbutton Confirm that pushbutton height and location conform to specifications and can be reached by a person in a wheelchair, from a hard surfaced level...
-
Adjustable height/gap protocol
Number of subjects that were able to attain a certain gap at a certain height under adjustable height/gap protocol Height\Gap 3.5" 7"...
-
11B-226.3 Dining surfaces exceeding 34 inches in height
Where food or drink is served for consumption at a counter exceeding 34 inches (864 mm) in height, a portion of the main counter 60 inches (1525 mm) minimum in length shall be provided in...
-
Access Board: Signs
-
M301 Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position
[See subsections ...]
-
How Can You Overcome These Barriers to Work with Your Providers?
There are many things that a person with a disability can do to improve his or her quality of health care and break down the barriers that compromise care. The following suggestions...
-
M301 Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position
[See subsections ...]
-
Protocol B Heights Obtained
Again for the minimum height protocol HERL participants transferred lower on average than the NDVWSC participants....
-
11B-611.4 Height
11B-611.4 Height. Top loading machines shall have the door to the laundry compartment located 36 inches (914 mm) maximum above the finish floor....
-
Boost Your Business - Chapter 11 - Stairs
Boost Your Business - Chapter 11 - Stairs
-
Appendix 3 - Comparison of US Standards to IDEA Center Research
(HH) 915 80 895 754 1024 Armrest Height (AH) 760...
-
11B-611.4 Height
FIGURE 11B-611.4 HEIGHT OF LAUNDRY COMPARTMENT OPENING...
-
Priority 2: Access to Goods & Services
Word Fillable Form (2.5MB) Word Non-Fillable Form (2.4MB) PDF Non-Fillable Form (1.4MB)
-
3.3.7 Toe Clearance Height, minimum
3.3.7 Toe Clearance Height, minimum There is relatively large disparity between the standards for toe clearance height, with the U.S. having the lowest (230 mm or 9 in.), followed by...
-
36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
Published in the Federal Register on January 9, 2017. RIN 3014-AA40 AGENCY: Architectural and Transportation Barriers Compliance Board. ACTION: Final rule. SUMMARY: The...
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2.
-
36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
Published in the Federal Register on January 9, 2017. 36 CFR Part 1195 RIN 3014-AA40 Standards for Accessible Medical Diagnostic Equipment AGENCY: Architectural and...
