Accessible dining surfaces and work surfaces for children’s use shall comply with Section 11B-902.4....
Search Results "Transfer Surface Height"
Filters
Commonly Searched Documents
-
11B-902.4 Dining surfaces and work surfaces for children’s use
-
11B-902.4 Dining surfaces and work surfaces for children’s use
Accessible dining surfaces and work surfaces for children’s use shall comply with Section 11B-902.4....
-
11B-902.4 Dining surfaces and work surfaces for children’s use
Accessible dining surfaces and work surfaces for children’s use shall comply with Section 11B-902.4....
-
Size and Clearances [4.21.2]
Size and Clearances [4.21.2] Clear floor space is specified for side transfers. Where a forward approach is provided, space at least 60 inches wide provides room for turning....
-
Firmness, Stability, and Slip Resistance [§302.1]
Firmness, Stability, and Slip Resistance [§302.1] Accessible floor and ground surfaces must be stable, firm, and slip resistant....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
IV. Discussion of Findings and Implications
of surface maintenance to assure accessibility and safety for use by children on a daily basis. ...
-
11B-242.4 Spas
Accessible means of entry shall comply with swimming pool lifts complying with Section 11B-1009.2; transfer walls complying with Section 11B-1009.4; or transfer systems complying with Section...
-
11B-242.4 Spas
Accessible means of entry shall comply with swimming pool lifts complying with Section 11B-1009.2; transfer walls complying with Section 11B-1009.4; or transfer systems complying with Section...
-
11B-242.4 Spas
Accessible means of entry shall comply with swimming pool lifts complying with Section 11B-1009.2; transfer walls complying with Section 11B-1009.4; or transfer systems complying with Section...
-
General [4.5.1]
Design guidelines cannot encompass all criteria contributing to the safety of a walking surface....
-
410.2 Floor Surfaces
Floor surfaces in platform lifts shall comply with 302 and 303....
-
410.2 Floor Surfaces
Floor surfaces in platform lifts shall comply with 302 and 303....
-
11B-703.5.5 Character height
Minimum character height shall comply with Table 11B-703.5.5....
-
1015.3 Height
Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: From the adjacent walking surfaces....
-
R408.4 Tread Surface
R408.4 Tread Surface. Stairway treads shall comply with R302.7. Changes in level are not permitted....
-
4.8.5* HANDRAILS
(2) If handrails are not continuous, they shall extend at least 12 in (305 mm) beyond the top and bottom of the ramp segment and shall be parallel with the floor or ground surface....
-
11B-605.2 Height and depth
Urinals shall be the stall-type or the wall-hung type with the rim 17 inches (432 mm) maximum above the finish floor or ground. Urinals shall be 13½ inches (343 mm) deep minimum...
-
Width [4.7.3] and Surface [4.7.4]
Curb ramp surfaces, including flared sides, must comply with requirements in 4.5 for ground and floor surfaces be "stable, firm, and slip resistant."...
-
General: ADA Standard Section 303.1
Section 303.1 of the ADA Standards covers information in the current ADA Standards for changes in level for floor and ground surfaces.
-
11B-608.3.1 Transfer type shower compartments
In transfer type compartments, grab bars shall be provided across the control wall and back wall to a point 18 inches (457 mm) from the control wall....
-
M305 Supports (Section-by-Section Analysis)
M305 in the final rule provides the technical requirements for transfer supports, standing supports, leg supports, and head and back supports....
-
609.5 Surface Hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
609.5 Surface Hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....